- 您现在的位置：买卖IC网 > Datasheet目录995 > NCP1013LEDGEVB (ON Semiconductor)BOARD EVAL 5W UNIV LED DRIVER Datasheet资料下载
参数资料
| 型号： | NCP1013LEDGEVB |
| 厂商： | ON Semiconductor |
| 文件页数： | 12/24页 |
| 文件大小： | 0K |
| 描述： | BOARD EVAL 5W UNIV LED DRIVER |
| 设计资源： | NCP1013LEDGEVB Schematic NCP1013LEDGEVB Gerber Files NCP1013LEDGEVB Bill of Materials |
| 标准包装： | 1 |
| 电流 - 输出 / 通道： | 700mA |
| 输出及类型： | 1，隔离 |
| 输出电压： | 8.6V |
| 特点： | 短路保护 |
| 输入电压： | 85 ~ 265VAC |
| 已供物品： | 板 |
| 已用 IC / 零件： | NCP1013 |
| 其它名称： | NCP1013LEDGEVB-ND NCP1013LEDGEVBOS |
NCP1010, NCP1011, NCP1012, NCP1013, NCP1014
VCC ON = 8.5 V
VCC OFF = 7.5 V
Drain
+
--
+
Startup Source
+
V CC
Rlimit
D1
--
+
Vclamp = 8.7 V typ.
+
CVcc
+
Caux
Laux
Permanent
+
Latch
--
+
I > 7.4m
(Typ.)
Ground
Figure 18. A more detailed view of the NCP101X offers better insight on how to
properly wire an auxiliary winding.
> 30 ms
Figure 19. The burst frequency becomes so low that it is difficult to keep
an adequate level on the auxiliary V CC . . .
Lowering the Standby Power with Skip--Cycle
Skip--cycle offers an efficient way to reduce the standby
power by skipping unwanted cycles at light loads.
However, the recurrent frequency in skip often enters the
audible range and a high peak current obviously generates
acoustic noise in the transformer. The noise takes its origins
in the resonance of the transformer mechanical structure
which is excited by the skipping pulses. A possible
solution, successfully implemented in the NCP1200 series,
also authorizes skip--cycle but only when the power
demand has dropped below a given level. At this time, the
peak current is reduced and no noise can be heard.
Figure 20 pictures the peak current evolution of the
NCP101X entering standby.
http://onsemi.com
12
相关PDF资料 |
PDF描述 |
|---|---|
| NCP1028LEDGEVB | EVAL BOARD FOR NCP1028LEDG |
| NCP1216AFORWGEVB | BOARD EVAL NCP1216A 35W |
| NCP1351LEDGEVB | EVAL BOARD FOR NCP1351LEDG |
| NCP3065BBGEVB | BOARD EVAL NCP3065 MR16 BOOST |
| NCP3066SCBCKGEVB | EVAL BOARD FOR NCP3066SCBCKG |
相关代理商/技术参数 |
参数描述 |
|---|---|
| NCP1013ST100T3 | 功能描述:电流型 PWM 控制器 Low Standby Power RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| NCP1013ST100T3G | 功能描述:电流型 PWM 控制器 Low Standby Power Monolithic Switcher RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| NCP1013ST130T3 | 功能描述:电流型 PWM 控制器 Low Standby Power RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| NCP1013ST130T3G | 功能描述:电流型 PWM 控制器 Low Standby Power Monolithic Switcher RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| NCP1013ST65T3 | 功能描述:电流型 PWM 控制器 Low Standby Power RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
发布紧急采购，3分钟左右您将得到回复。