- 您现在的位置：买卖IC网 > PDF目录361090 > NCP1117DT18G (ON SEMICONDUCTOR) 1.0 A Low−Dropout Positive Fixed and Adjustable Voltage Regulators PDF资料下载
参数资料
| 型号： | NCP1117DT18G |
| 厂商： | ON SEMICONDUCTOR |
| 元件分类： | 基准电压源/电流源 |
| 英文描述： | 1.0 A Low−Dropout Positive Fixed and Adjustable Voltage Regulators |
| 中文描述： | 1.8 V FIXED POSITIVE LDO REGULATOR, 1.2 V DROPOUT, PSSO2 |
| 封装： | LEAD FREE, DPAK-3 |
| 文件页数： | 9/17页 |
| 文件大小： | 178K |
| 代理商： | NCP1117DT18G |
NCP1117, NCV1117
http://onsemi.com
9
Protection Diodes
The NCP1117 family has two internal low impedance
diode paths that normally do not require protection when
used in the typical regulator applications. The first path
connects between V
out
and V
in
, and it can withstand a peak
surge current of about 15 A. Normal cycling of V
in
cannot
generate a current surge of this magnitude. Only when V
in
is shorted or crowbarred to ground and C
out
is greater than
50 F, it becomes possible for device damage to occur.
Under these conditions, diode D1 is required to protect the
device. The second path connects between C
adj
and V
out
, and
it can withstand a peak surge current of about 150 mA.
Protection diode D2 is required if the output is shorted or
crowbarred to ground and C
adj
is greater than 1.0 F.
Figure 22. Protection Diode Placement
1
2
Output
3
Input
NCP1117
XTA
+
+
C
out
C
in
R2
+
C
adj
R1
1N4001
D1
D2
1N4001
A combination of protection diodes D1 and D2 may be
required in the event that V
in
is shorted to ground and C
adj
is greater than 50 F. The peak current capability stated for
the internal diodes are for a time of 100 s with a junction
temperature of 25
°
C. These values may vary and are to be
used as a general guide.
Load Regulation
The NCP1117 series is capable of providing excellent
load regulation; but since these are three terminal devices,
only partial remote load sensing is possible. There are two
conditions that must be met to achieve the maximum
available load regulation performance. The first is that the
top side of programming resistor R1 should be connected as
close to the regulator case as practicable. This will minimize
the voltage drop caused by wiring resistance RW + from
appearing in series with reference voltage that is across R1.
The second condition is that the ground end of R2 should be
connected directly to the load. This allows true Kelvin
sensing where the regulator compensates for the voltage
drop caused by wiring resistance RW .
Figure 23. Load Sensing
1
2
Output
3
Input
NCP1117
XTA
+
+
C
out
C
in
R1
Remote
Load
RW+
RW
R2
Thermal Considerations
This series contains an internal thermal limiting circuit
that is designed to protect the regulator in the event that the
maximum junction temperature is exceeded. When
activated, typically at 175
°
C, the regulator output switches
off and then back on as the die cools. As a result, if the device
is continuously operated in an overheated condition, the
output will appear to be oscillating. This feature provides
protection from a catastrophic device failure due to
accidental overheating. It is not intended to be used as a
substitute for proper heatsinking. The maximum device
power dissipation can be calculated by:
PD
TJ(max)
TA
RJA
The devices are available in surface mount SOT223 and
DPAK packages. Each package has an exposed metal tab
that is specifically designed to reduce the junction to air
thermal resistance, R
JA
, by utilizing the printed circuit
board copper as a heat dissipater. Figures 18 and 19 show
typical R
JA
values that can be obtained from a square
pattern using economical single sided 2.0 ounce copper
board material. The final product thermal limits should be
tested and quantified in order to insure acceptable
performance and reliability. The actual R
JA
can vary
considerably from the graphs shown. This will be due to any
changes made in the copper aspect ratio of the final layout,
adjacent heat sources, and air flow.
相关PDF资料 |
PDF描述 |
|---|---|
| NCP1117DT19RKG | 1.0 A Low−Dropout Positive Fixed and Adjustable Voltage Regulators |
| NCP1117DT20G | 1.0 A Low−Dropout Positive Fixed and Adjustable Voltage Regulators |
| NCP1117DT20RKG | 1.0 A Low−Dropout Positive Fixed and Adjustable Voltage Regulators |
| NCP1117DT25G | 1.0 A Low−Dropout Positive Fixed and Adjustable Voltage Regulators |
| NCP1117DT25T5G | 1.0 A Low−Dropout Positive Fixed and Adjustable Voltage Regulators |
相关代理商/技术参数 |
参数描述 |
|---|---|
| NCP1117DT18G | 制造商:ON Semiconductor 功能描述:VOLTAGE REG IC |
| NCP1117DT18RK | 功能描述:低压差稳压器 - LDO 1.8V 1A Positive RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| NCP1117DT18RKG | 功能描述:低压差稳压器 - LDO 1.8V 1A Positive RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| NCP1117DT18T5 | 功能描述:低压差稳压器 - LDO 1.8V 1A Positive RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| NCP1117DT18T5G | 功能描述:低压差稳压器 - LDO 1.8V 1A Positive RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
发布紧急采购，3分钟左右您将得到回复。