- 您现在的位置：买卖IC网 > PDF目录19654 > NCP1216AP65G (ON Semiconductor)IC CTRLR PWM CM OTP HV 8DIP PDF资料下载
参数资料
| 型号： | NCP1216AP65G |
| 厂商： | ON Semiconductor |
| 文件页数： | 14/18页 |
| 文件大小： | 0K |
| 描述： | IC CTRLR PWM CM OTP HV 8DIP |
| 标准包装： | 50 |
| 输出隔离： | 隔离 |
| 频率范围： | 58.5kHz ~ 71.5kHz |
| 输入电压： | 11 V ~ 16 V |
| 工作温度： | 0°C ~ 125°C |
| 封装/外壳： | 8-DIP（0.300"，7.62mm），7 引线 |
| 供应商设备封装： | 7-PDIP |
| 包装： | 管件 |
NCP1216, NCP1216A
D t + D V·C (eq. 19)
depends on the startup sequence of your system, i.e. when
you first apply the power to the IC. The corresponding
transient fault duration due to the output capacitor charging
must be less than the time needed to discharge from 12.2 V
to 10 V, otherwise the supply will not properly start. The test
consists in either simulating or measuring in the lab how
much time the system takes to reach the regulation at full
load. Let’s suppose that this time corresponds to 6ms.
Therefore a V CC fall time of 10 ms could be well
appropriated in order to not trigger the overload detection
circuitry. If the corresponding IC consumption, including
the MOSFET drive, establishes at 2.9 mA, we can calculate
the required capacitor using the following formula:
i
with D V = 2.2 V. Then for a wanted D t of 30 ms, C equals
39.5 m F or a 68 m F for a standard value (including ± 20%
dispersions). When an overload condition occurs, the IC
blocks its internal circuitry and its consumption drops to
350 m A typical. This happens at V CC = 10 V and it remains
stuck until V CC reaches 5.6 V: we are in latchoff phase.
Again, using the selected 68 m F and 350 m A current
consumption, this latchoff phase lasts: 780 ms.
Protecting the Controller Against Negative Spikes
As with any controller built upon a CMOS technology, it
is the designer ’s duty to avoid the presence of negative
spikes on sensitive pins. Negative signals have the bad habit
to forward bias the controller substrate and induce erratic
behaviors. Sometimes, the injection can be so strong that
internal parasitic SCRs are triggered, engendering
irremediable damages to the IC if a low impedance path is
offered between V CC and GND. If the current sense pin is
often the seat of such spurious signals, the high ? voltage pin
can also be the source of problems in certain circumstances.
During the turn ? off sequence, e.g. when the user unplugs the
power supply, the controller is still fed by its V CC capacitor
and keeps activating the MOSFET ON and OFF with a peak
current limited by R sense . Unfortunately, if the quality
coefficient Q of the resonating network formed by L p and
C bulk is low (e.g. the MOSFET R dson + R sense are small),
conditions are met to make the circuit resonate and thus
negatively bias the controller. Since we are talking about ms
pulses, the amount of injected charge, (Q = I * t),
immediately latches the controller that brutally discharges
its V CC capacitor. If this V CC capacitor is of sufficient value,
its stored energy damages the controller. Figure 26 depicts
a typical negative shot occurring on the HV pin where the
brutal V CC discharge testifies for latchup.
0
V CC
5 V/DIV
10 ms/DIV
V latch
1 V/DIV
Figure 26. A Negative Spike Takes Place on the Bulk Capacitor at the Switch ? off Sequence
Simple and inexpensive cures exist to prevent from
internal parasitic SCR activation. One of them consists in
inserting a resistor in series with the high ? voltage pin to
keep the negative current to the lowest when the bulk
becomes negative (Figure 27). Please note that the negative
Another option (Figure 28) consists in wiring a diode
from V CC to the bulk capacitor to force V CC to reach
VCC ON sooner and thus stops the switching activity before
the bulk capacitor gets deeply discharged. For security
reasons, two diodes can be connected in series.
spike is clamped to ( ? 2 * V f ) due to the diode bridge. Also,
the power dissipation of this resistor is extremely small since
it only heats up during the startup sequence.
http://onsemi.com
14
相关PDF资料 |
PDF描述 |
|---|---|
| EBT156-6A1X | CONN EDGEBOARD SINGLE 6POS 5A |
| TAJT225M035RNJ | CAP TANT 2.2UF 35V 20% 1210 |
| EBC10DCSH | CONN EDGECARD 20POS DIP .100 SLD |
| RW2-1212S/H2 | CONV DC/DC 2W 9-18VIN 12VOUT |
| ABE35DHHT | CONN EDGECARD 70POS 1MM DIP SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| NCP1216D100 | 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:PWM Current-Mode Controller for High-Power Universal Off-Line Supplies |
| NCP1216D100R2 | 功能描述:电流型 PWM 控制器 Current Mode PWM RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| NCP1216D100R2G | 功能描述:电流型 PWM 控制器 Current Mode PWM RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| NCP1216D133 | 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:PWM Current-Mode Controller for High-Power Universal Off-Line Supplies |
| NCP1216D133R2 | 功能描述:电流型 PWM 控制器 Current Mode PWM RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
发布紧急采购，3分钟左右您将得到回复。