- 您现在的位置：买卖IC网 > PDF目录19524 > NCP1217AD100R2 (ON Semiconductor)IC CTRLR PWM CM OVP HV 8SOIC PDF资料下载
参数资料
| 型号： | NCP1217AD100R2 |
| 厂商： | ON Semiconductor |
| 文件页数： | 13/19页 |
| 文件大小： | 0K |
| 描述： | IC CTRLR PWM CM OVP HV 8SOIC |
| 产品变化通告： | LTB Notification 03/Jan/2008 |
| 标准包装： | 2,500 |
| 输出隔离： | 隔离 |
| 频率范围： | 90kHz ~ 110kHz |
| 输入电压： | 8.3 V ~ 16 V |
| 工作温度： | 0°C ~ 125°C |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 8-SOICN |
| 包装： | 带卷 (TR) |
NCP1217, NCP1217A
V CC
The startup current source keeps the
VCC ON = 12.8 V
VCC min = 7.6 V
device latched until reset occurs.
VCC latch = 5.6 V
Drv
Reset level
Time
Adj
Driver
Pulses
Latched--off
Time
Default
adj level
Fault brings adj above latching level
Time
Figure 24. When Vadj is Pulled Above 3.1 V, NCP1217 Permanently Latches--Off the Output Pulses
In normal operation, the Adj pin level is kept at a fixed
level, the default one or lower. As soon as some external
signal pulls this Adj pin level above 3.1 V typical, the output
pulses are permanently disabled. Care must be taken to limit
the injected current into pin 1 to less than 2.0 mA, e.g.
Vaux
through a series resistor of 5.6 k with a 10 V V CC . The
startup switch is activated every time V CC reaches 5.6 V and
maintains a V CC voltage ramping up and down between
5.6 V and 12.8 V. Reset occurs when V CC falls below 5.6 V,
e.g. when the user cycle the SMPS down. Figure 25
illustrates the operation. Adding a zener diode from Q1 base
to ground makes a cheap OVP, protecting the supply from
any lethal open--loop operation. If a thermistor (NTC) is
T
OVP
1
2
3
4
8
7
6
5
< 16 V
CV CC
Laux
added in parallel with the Zener--diode, overtemperature
protection is also ensured.
Figure 25. A Thermistor and a Zener Diode Offer
Both OVP and Overtemperature Latched--Off
Protection
Nonlatching Shutdown
In some cases, it might be desirable to shut off the part
temporarily and authorize its restart once the default has
disappeared. This option can easily be accomplished
through a single NPN bipolar transistor wired between FB
and ground. By pulling FB below the Adj Pin 1 level, the
output pulses are disabled as long as FB is pulled below
Pin 1. As soon as FB is relaxed, the IC resumes its operation.
Figure 26 depicts the application example.
http://onsemi.com
13
相关PDF资料 |
PDF描述 |
|---|---|
| VE-B5P-CX-B1 | CONVERTER MOD DC/DC 13.8V 75W |
| AP1084D50L-U | IC REG LDO 5V 5A TO-252 |
| TPSB107K004R0350 | CAP TANT 100UF 4V 10% 1210 |
| V150A12E400B | CONVERTER MOD DC/DC 12V 400W |
| VE-B5L-CW-B1 | CONVERTER MOD DC/DC 28V 100W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| NCP1217AD100R2G | 功能描述:电流型 PWM 控制器 Current Mode PWM w/50% Duty Cycle Max RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| NCP1217AD133R2 | 功能描述:电流型 PWM 控制器 Current Mode PWM RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| NCP1217AD133R2G | 功能描述:电流型 PWM 控制器 Current Mode PWM w/50% Duty Cycle Max RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| NCP1217AD65R2 | 功能描述:电流型 PWM 控制器 Current Mode PWM RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| NCP1217AD65R2G | 功能描述:电流型 PWM 控制器 Current Mode PWM w/50% Duty Cycle Max RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
发布紧急采购，3分钟左右您将得到回复。