- 您现在的位置：买卖IC网 > PDF目录19685 > NCP1230D165R2G (ON Semiconductor)IC CTLR PWM SMPS 165KHZ 7-SOIC PDF资料下载
参数资料
| 型号： | NCP1230D165R2G |
| 厂商： | ON Semiconductor |
| 文件页数： | 14/21页 |
| 文件大小： | 0K |
| 描述： | IC CTLR PWM SMPS 165KHZ 7-SOIC |
| 标准包装： | 1 |
| 输出隔离： | 隔离 |
| 频率范围： | 65kHz |
| 输入电压： | 8.4 V ~ 18 V |
| 工作温度： | -40°C ~ 125°C |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽）7 引线 |
| 供应商设备封装： | 7-SOIC |
| 包装： | 剪切带 (CT) |
| 其它名称： | NCP1230D165R2GOSCT |
NCP1230
Leading Edge Blanking
In Switch Mode Power Supplies (SMPS) there can be a
large current spike at the beginning of the current ramp due
to the Power Switch gate to source capacitance, transformer
interwinding capacitance, and output rectifier recovery
time. To prevent prematurely turning off the PWM drive
output, a Leading Edges Blanking (LEB) (Figure 34) circuit
is place is series with the current sense input, and PWM
comparator. The LEB circuit masks the first 250 ns of the
current sense signal.
Thermal Shutdown
Skip
125 msec Timer
isolated secondary output and on the auxiliary winding.
Because the auxiliary winding and diode form a peak
rectifier, the auxiliary Vcc capacitor voltage can be charged
up to the peak value rather than the true plateau which is
proportional to the output level.
To resolve these issues the NCP1230 monitors the 1.0 V
error flag. As soon as the internal 1.0 V error flag is asserted
high, a 125 ms timer starts. If at the end of the 125 ms timeout
period, the error flag is still asserted then the controller
determines that there is a true fault condition and stops the
PWM drive output, refer to Figure 35. When this occurs,
Vcc starts to decrease because the power supply is locked
out. When Vcc drops below UVLOlow (7.7 V typical), it
FB/3
Vccreset
CS
S
250 ns
10 V
Latch ? Off
3
2.3 Vpp PWM Comparator
Ramp -
18 k
LEB +
3V
+
-
Figure 34.
R Q
enters a latch ? off phase where the internal consumption is
reduced down to 680 m A (typical). The voltage on the Vcc
capacitor continues to drop, but at a lower rate. When Vcc
reaches the latch ? off level (5.6 V), the current source is
turned on and pulls Vcc above UVLOhigh. To limit the fault
output power, a divide ? by ? two circuit is connected to the
Vcc pin that requires two startup sequences before
attempting to restart the power supply. If the fault has gone
and the error flag is low, the controller resumes normal
operations.
Under transient load conditions, if the error flag is
Short ? Circuit Condition
The NCP1230 is different from other controllers which
use an auxiliary windings to detect events on the isolated
secondary output. There maybe some conditions (for
example when the leakage inductance is high) where it can
be extremely difficult to implement short ? circuit and
overload protection. This occurs because when the power
switch opens, the leakage inductance superimposes a large
spike on the switch drain voltage. This spike is seen on the
asserted, the error flag will normally drop prior to the 125 ms
timeout period and the controller continues to operate
normally.
If the 125 msec timer expires while the NCP1230 is in the
Skip Mode, SW1 opens and the PFC_Vcc output will shut
down and will not be activated until the fault goes away and
the power supply resumes normal operations.
While in the Skip Mode, to avoid any thermal runaway it
is desirable for the Burst duty cycle to be kept below
20%(the burst duty ? cycle is defined as Tpulse / Tfault).
http://onsemi.com
14
相关PDF资料 |
PDF描述 |
|---|---|
| GMC44DRYN-S734 | CONN EDGECARD 88POS DIP .100 SLD |
| V110A12E400B2 | CONVERTER MOD DC/DC 12V 400W |
| GSM02DRUN | CONN EDGECARD 4POS DIP .156 SLD |
| GSC44DRYH-S734 | CONN EDGECARD 88POS DIP .100 SLD |
| V110A12E400B | CONVERTER MOD DC/DC 12V 400W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| NCP1230D65R2 | 功能描述:电流型 PWM 控制器 Low Standby Power RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| NCP1230D65R2G | 功能描述:电流型 PWM 控制器 Low Standby Power High Performance PWM RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| NCP1230GEVB | 功能描述:电源管理IC开发工具 ANA NCP1230 EVAL BOARD RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| NCP1230P100 | 功能描述:交流/直流开关转换器 Low Standby Power RoHS:否 制造商:STMicroelectronics 输出电压:800 V 输入/电源电压（最大值）:23.5 V 输入/电源电压（最小值）:11.5 V 开关频率:115 kHz 电源电流:1.6 mA 工作温度范围:- 40 C to + 150 C 安装风格:SMD/SMT 封装 / 箱体:SSO-10 封装:Reel |
| NCP1230P100G | 功能描述:电流型 PWM 控制器 Low Standby Power High Performance PWM RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
发布紧急采购，3分钟左右您将得到回复。