- 您现在的位置：买卖IC网 > PDF目录19615 > NCP1246BD065R2G (ON Semiconductor)IC CTLR CURR MODE 65KHZ 8SOIC PDF资料下载
参数资料
| 型号： | NCP1246BD065R2G |
| 厂商： | ON Semiconductor |
| 文件页数： | 37/39页 |
| 文件大小： | 0K |
| 描述： | IC CTLR CURR MODE 65KHZ 8SOIC |
| 标准包装： | 2,500 |
| 系列： | * |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页当前第37页第38页第39页
NCP1246
Latch ? Off Input
Figure 70. Latch Detection Schematic
The Latch pin is dedicated to the latch ? off function: it
includes two levels of detection that define a working
window, between a high latch and a low latch: within these
two thresholds, the controller is allowed to run, but as soon
as either the low or the high threshold is crossed, the
controller is latched off. The lower threshold is intended to
be used with an NTC thermistor, thanks to an internal current
source I NTC .
An active clamp prevents the voltage from reaching the
high threshold if it is only pulled up by the I NTC current. To
reach the high threshold, the pull ? up current has to be higher
than the pull ? down capability of the clamp (typically
1.5 mA at V OVP ).
To avoid any false triggering, spikes shorter than 50 m s
(for the high latch and 65 kHz version) or 350 m s (for the low
latch) are blanked and only longer signals can actually latch
the controller.
Reset occurs when a brown ? out condition is detected or
the V CC is cycled down to a reset voltage, which in a real
application can only happen if the power supply is
unplugged from the ac line.
Upon startup, the internal references take some time
before being at their nominal values; so one of the
comparators could toggle even if it should not. Therefore the
internal logic does not take the latch signal into account
before the controller is ready to start: once V CC reaches
V CC(on) , the latch pin High latch state is taken into account
and the DRV switching starts only if it is allowed; whereas
the Low latch (typically sensing an over temperature) is
taken into account only after the soft ? start is finished. In
addition, the NTC current is doubled to I NTC(SSTART) during
the soft ? start period, to speed up the charging of the Latch
pin capacitor. The maximum value of Latch pin capacitor is
given by the following formula (The standard start ? up
condition is considered and the NTC current is neglected):
C LATCH
max
+
t SSTART
min @ I NTC(SSTART) min
V clamp0 min
+
8.0 @ 10 ? 3 @ 130 @ 10 ? 6
1.0
F + 1.04 m F (eq. 4)
http://onsemi.com
37
相关PDF资料 |
PDF描述 |
|---|---|
| RCM10DCBD-S189 | CONN EDGECARD 20POS R/A .156 SLD |
| 178-015-513R571 | CONN DB15 FEM-FEM .750" SPACING |
| TAP155K050HSB | CAP TANT 1.5UF 50V 10% RADIAL |
| ACB56DHFD-S621 | EDGECARD 112POS SMD W/O POST |
| MIC5247-1.6BM5 TR | IC REG LDO 1.6V .15A SOT23-5 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| NCP1246BD100R2G | 功能描述:电流型 PWM 控制器 FIXED FREQ (65KHZ) CURREN RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| NCP1246-D | 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:Fixed Frequency Current Mode Controller for Flyback Converters |
| NCP1247 | 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:Fixed Frequency Current Mode Controller for Flyback Converters |
| NCP1247AD065R2G | 制造商:ON Semiconductor 功能描述:REEL / FIXED FREQ A (65KHZ) CURR |
| NCP1247AD100R2G | 制造商:ON Semiconductor 功能描述:REEL - FIXED FREQ A (100KHZ) CUR |
发布紧急采购，3分钟左右您将得到回复。