参数资料
| 型号： | NCP1252ADR2G |
| 厂商： | ON Semiconductor |
| 文件页数： | 14/18页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR FLYBK ISO PWM 8SOIC |
| 标准包装： | 2,500 |
| PWM 型： | 电流模式 |
| 输出数： | 1 |
| 频率 - 最大： | 500kHz |
| 占空比： | 50% |
| 电源电压： | 9 V ~ 28 V |
| 降压： | 无 |
| 升压： | 无 |
| 回扫： | 是 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 是 |
| 工作温度： | -25°C ~ 125°C |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 包装： | 带卷 (TR) |
| 其它名称： | NCP1252ADR2G-ND NCP1252ADR2GOSTR |
NCP1252
V BO V bulkon * V BO
R BOlo + * 1
I BO
V bulkoff * V BO
R BOup +
V bulkon * V bulkoff
I BO
R BOlo + 1 370 * 1 * 1 + 5731 W
R BOup + 370 * 350 + 2.0 M W
(eq. 4)
R BOup can be also written independently of R BOlo by
substituting Equation 4 into Equation 3 as follow:
(eq. 5)
From Equation 4 and Equation 5, the resistor divider value
can be calculated:
10 m 350 * 1
10 m
Short Circuit or Over Load Protection:
A short circuit or an overload situation is detected when
the CS pin level reaching its maximum level at 1 V. In that
case the fault status is stored in the latch and allows the
digital timer count. If the digital timer ends then the fault is
latched and the controller permanently stops the pulses on
the driver pin.
If the fault is gone before ending the digital timer, the
timer is reset only after 3 switching controller periods
without fault detection (or when the CS pin < 1 V during at
least 3 switching periods).
If the fault is latched the controller can be reset if a BO
reset is sensed or if V CC is cycled down to V CC(off) .
Fault timer: 15 ms
CS pin
(500 mV/div)
12 Vout
Short Circuit
(5 V/div)
Time
(4 ms/div)
Figure 35. Short Circuit Detection Example
Shut Down
There is one possibility to shut down the controller; this
possibility consists at grounding the BO pin as illustrated in
Figure 34.
Ramp Compensation
Ramp compensation is a known mean to cure
subharmonic oscillations. These oscillations take place at
half of the switching frequency and occur only during
Continuous Conduction Mode (CCM) with a duty ? cycle
close to and above 50%. To lower the current loop gain, one
usually injects between 50 and 100% of the inductor
downslope. depicts how internally the ramp is generated:
The ramp compensation applied on CS pin is from the
internal oscillator ramp buffered. A switch placed between
the buffered internal oscillator ramp and R ramp disconnects
the ramp compensation during the OFF time DRV signal.
http://onsemi.com
14
相关PDF资料 |
PDF描述 |
|---|---|
| NCP1271P65G | IC CTRLR PWM CM OVP OTP HV 7DIP |
| NCP1280DR2G | IC CTRLR PWM PROG OVP HV 16SOIC |
| NCP1282BDR2G | IC REG CTRLR BST FLYBK VM 16SOIC |
| NCP1288BD65R2G | IC REG CTRLR FLYBACK PWM 7SOIC |
| NCP1294EDR2G | IC PWM CTLR FLYBACK 16SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| NCP1252APG | 功能描述:电流型 PWM 控制器 RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| NCP1252BDR2G | 功能描述:电流型 PWM 控制器 CURR MDE PWM CNTRLR FWD FLYBCK APPS RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| NCP1252CDR2G | 功能描述:电流型 PWM 控制器 NCP1252C PWM CONTROLLER RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| NCP1252TSFWDGEVB | 功能描述:电源管理IC开发工具 NCP1252 2-SWITCH FWD DB RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| NCP1253 | 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:Current-Mode PWM Controller for Off-line Power Supplies |
发布紧急采购，3分钟左右您将得到回复。