- 您现在的位置：买卖IC网 > PDF目录19583 > NCP1377P (ON Semiconductor)IC CTRLR PWM CM OVP UVLO 8DIP PDF资料下载
参数资料
| 型号： | NCP1377P |
| 厂商： | ON Semiconductor |
| 文件页数： | 9/17页 |
| 文件大小： | 0K |
| 描述： | IC CTRLR PWM CM OVP UVLO 8DIP |
| 产品变化通告： | LTB Notification 03/Jan/2008 |
| 标准包装： | 50 |
| 输出隔离： | 隔离 |
| 频率范围： | 100kHz |
| 输入电压： | 8.2 V ~ 18 V |
| 工作温度： | -40°C ~ 125°C |
| 封装/外壳： | 8-DIP（0.300"，7.62mm），7 引线 |
| 供应商设备封装： | 7-PDIP |
| 包装： | 管件 |
| 其它名称： | NCP1377POS |
NCP1377, NCP1377B
Drain
Signal
Timeout
Signal
Demag Restart
Current Sense and Timeout Restart
Drain
Signal
Timeout
Signal
5 m s
5 m s
Figure 20. When the primary natural ringing becomes too low, the internal TimeOut
together with the sense comparator initiates a new cycle when FB passes the skip level.
An optocoupler is generally used to transfer the feedback
information to the FB pin while providing the necessary
isolation. It introduces a limitation in how low the skip
level can be adjusted since an optocoupler cannot pull the
FB voltage below its Vce(sat), which is usually around
150 mV. Therefore, in order to take into account
temperature and process variations, it is not recommended
to set up the skip level below 250 mV, which corresponds
to a minimum resistor Rskip of 420 W . The 150 mV is a
much lower level than what will usually be used (it sets the
peak current when entering skip mode at 5% of the
7.0
maximum peak current). If anyway a lower skip threshold
is needed, care must be taken to select an optocoupler with
a Vce(sat) guaranteed to be below the chosen skip level
with enough margin.
Demagnetization Detection
The core reset detection is done by monitoring the
voltage activity on the auxiliary winding. This voltage
features a FLYBACK polarity. The typical detection level
is fixed at 50 mV as exemplified by Figure 21.
5.0
POSSIBLE
RESTARTS
TO INTERNAL
3.0
COMPARATOR
2
R esd
1
1
5
R dem
4
1.0
? 1.0
0V
50 mV
R int
R esd + R int = 28 k
ESD2
ESD1
4
Aux
3
Figure 21. Core Reset Detection is Done through
a Dedicated Auxiliary Winding Monitoring
http://onsemi.com
9
Figure 22. Internal Pad Implementation
相关PDF资料 |
PDF描述 |
|---|---|
| EPM7032STC44-10N | IC MAX 7000 CPLD 32 44-TQFP |
| ASM22DRST-S664 | CONN EDGECARD 44POS DIP .156 SLD |
| ISPLSI 5512VA-100LB388 | IC PLD ISP 288I/O 10NS 388BGA |
| VI-B0M-CY-F2 | CONVERTER MOD DC/DC 10V 50W |
| EPM7032STC44-10FN | IC MAX 7000 CPLD 32 44-TQFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| NCP1377PG | 功能描述:电流型 PWM 控制器 Quasi Resonant Current Mode PWM RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| NCP1378 | 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:PWM Current-Mode Controller for Free-Running Quasi-Resonant Operation |
| NCP1378/D | 制造商:未知厂家 制造商全称:未知厂家 功能描述:PWM Current-Mode Controller for Free Running Quasi-Resonant Operation |
| NCP1378_06 | 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:PWM Current−Mode Controller for Free−Running Quasi−Resonant Operation |
| NCP1378DR2 | 功能描述:电流型 PWM 控制器 Quasi Resonant RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
发布紧急采购，3分钟左右您将得到回复。