- 您现在的位置：买卖IC网 > PDF目录20420 > NCP1380DGEVB (ON Semiconductor)BOARD EVAL NCP1380 CURR CTLR PDF资料下载
参数资料
| 型号： | NCP1380DGEVB |
| 厂商： | ON Semiconductor |
| 文件页数： | 13/26页 |
| 文件大小： | 0K |
| 描述： | BOARD EVAL NCP1380 CURR CTLR |
| 设计资源： | NCP1380DGEVB Schematic NCP1380DGEVB Test Procedure NCP1380DGEVB Gerber Zip NCP1380DGEVB Bill of Materials |
| 标准包装： | 1 |
| 主要目的： | AC/DC，主面 |
| 输出及类型： | 1，隔离 |
| 输出电压： | 19V |
| 电流 - 输出： | 4A |
| 输入电压： | 85 ~ 265VAC |
| 稳压器拓扑结构： | 回扫 |
| 板类型： | 完全填充 |
| 已供物品： | 板 |
| 已用 IC / 零件： | NCP1380 |
| 其它名称： | NCP1380DGEVB-ND NCP1380DGEVBOS |
NCP1380
APPLICATION INFORMATION
The NCP1380 implements a standard current?mode
architecture operating in quasi?resonant mode. Due to a
proprietary circuitry, the controller prevents
valley?jumping instability and steadily locks out in selected
valley as the power demand goes down. Once the fourth
valley is reached, the controller continues to reduce the
? Fault input (A and B versions) : By combining a dual
threshold on the Fault pin, the controller allows the
direct connection of an NTC to ground plus a zener
diode to a monitored voltage. In case the pin is brought
below the OTP threshold by the NTC or above the OVP
threshold by the zener diode, the circuit permanently
frequency further down, offering excellent efficiency over
a wide operating range. Thanks to a fault timer combined to
an OPP circuitry, the controller is able to efficiently limit the
output power at high?line.
? Quasi?Resonance Current?mode operation :
implementing quasi?resonance operation in peak
current?mode control, the NCP1380 optimizes the
efficiency by switching in the valley of the MOSFET
drain?source voltage. Thanks to a proprietary circuitry,
the controller locks?out in a selected valley and
remains locked until the output loading significantly
changes. When the load becomes lighter, the controller
jumps into the next valley. It can go down to the 4 th
valley if necessary. Beyond this point, the controller
reduces its switching frequency by freezing the peak
current setpoint. During quasi?resonance operation, in
case of very damped valleys, a 5.5 m s timer emulates
the missing valleys.
? Frequency reduction in light?load conditions : when
the 4 th valley is left, the controller reduces the
switching frequency which naturally improves the
standby power by a reduction of all switching losses.
? Overpower protection (OPP) : When the voltage on
ZCD pin swings in flyback polarity, a direct image if
the input voltage is applied on ZCD pin. We can thus
reduce the peak current depending of V ZCD during the
on?time.
? Internal soft?start : A soft?start precludes the main
power switch from being stressed upon startup. Its
?
?
latches?off and V CC is clamped to 7.2 V.
Fault input (C and D versions) : The C and D versions
of NCP1380 include a brown?out circuit which safely
stops the controller in case the input voltage is too low.
Restart occurs via a complete startup sequence (latch
reset and soft?start). During normal operation, the
voltage on this pin is clamped to V clamp to give enough
room for OVP detection. If the voltage on this pin
increases above 2.5 V, the part latches?off.
Short?circuit protection : Short?circuit and especially
over?load protections are difficult to implement when a
strong leakage inductance between auxiliary and power
windings affects the transformer (where the auxiliary
winding level does not properly collapse in presence of
an output short). Here, when the internal 0.8 V
maximum peak current limit is activated, the timer
starts counting up. If the fault disappears, the timer
counts down. If the timer reaches completion while the
error flag is still present, the controller stops the pulses.
This protection is latched on A and C version (the user
must unplug and re?plug the power supply to restart the
controller) and auto?recovery on B and D versions (if
the fault disappears, the SMPS automatically resumes
operation). In addition, all versions feature a winding
short?circuit protection, that senses the CS signal and
stops the controller if V CS reaches 1.5 x V ILIM (after a
reduced LEB of t BCS ). This additional comparator is
enabled only during the main LEB duration t LEB , for
noise immunity reason.
duration is fixed and equal to 4 ms.
NCP1380 OPERATING MODES
NCP1380 has two operating mode: quasi?resonant
operation and VCO operation for the frequency foldback.
The operating mode is fixed by the FB voltage as
portrayed by Figure 26:
? Quasi?resonant operation occurs for FB voltage higher
than 0.8 V (FB decreasing) or higher than 1.4 V (FB
increasing) which correspond to high output power and
medium output power. The peak current is variable and
is set by the FB voltage divided by 4.
? Frequency foldback or VCO mode occurs for FB
voltage lower than 0.8 V (FB decreasing) or lower than
1.4 V (FB increasing). This corresponds to low output
power.
During VCO mode, the peak current decreases down to
17.5% of its maximum value and is then frozen. The
switching frequency is variable and decreases as the
output load decreases.
The switching frequency is set by the end of charge of
the capacitor connected to the C T pin. This capacitor is
charged with a constant current source and the
capacitor voltage is compared to an internal threshold
fixed by FB voltage. When this capacitor voltage
reaches the threshold the capacitor is rapidly discharged
down to 0 V and a new period start.
http://onsemi.com
13
相关PDF资料 |
PDF描述 |
|---|---|
| SDR0604-330KL | INDUCTOR POWER 33UH 0.88A SMD |
| GEC10DRXI-S734 | CONN EDGECARD 20POS DIP .100 SLD |
| VE-J3B-CW-F3 | CONVERTER MOD DC/DC 95V 100W |
| POE370U-480-16-N | POWER SUPPLY 16PORT GIGABIT |
| VE-J3B-CW-F2 | CONVERTER MOD DC/DC 95V 100W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| NCP1381 | 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:Low−Standby High Performance PWM Controller |
| NCP1381 AM90 WAF | 制造商:ON Semiconductor 功能描述: |
| NCP1381ADAPEVB | 功能描述:BOARD EVAL NCP1381 RoHS:是 类别:编程器，开发系统 >> 评估演示板和套件 系列:* 标准包装:1 系列:PCI Express® (PCIe) 主要目的:接口，收发器，PCI Express 嵌入式:- 已用 IC / 零件:DS80PCI800 主要属性:- 次要属性:- 已供物品:板 |
| NCP1381DR2G | 功能描述:电流型 PWM 控制器 ANA PWM CONTROLLER RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| NCP1382DR2G | 功能描述:电流型 PWM 控制器 L-STNDBY PWM CNTRLR RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
发布紧急采购，3分钟左右您将得到回复。