参数资料
| 型号： | NCP1396BDR2G |
| 厂商： | ON Semiconductor |
| 文件页数： | 13/25页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR ISO PWM VM 16-SOIC |
| 产品变化通告： | Package Pin Removal 11/Feb/2008 |
| 标准包装： | 1 |
| PWM 型： | 电压模式 |
| 输出数： | 1 |
| 频率 - 最大： | 575kHz |
| 占空比： | 52% |
| 电源电压： | 10.5 V ~ 20 V |
| 降压： | 无 |
| 升压： | 无 |
| 回扫： | 无 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 是 |
| 工作温度： | -40°C ~ 125°C |
| 封装/外壳： | 16-SOIC（0.154"，3.90mm 宽）15 引线 |
| 包装： | 标准包装 |
| 其它名称： | NCP1396BDR2GOSDKR |
NCP1396A, NCP1396B
Application Information
The NCP1396 A/B includes all necessary features to help
building a rugged and safe switch-- mode power supply
featuring an extremely low standby power. The below
bullets detail the benefits brought by implementing the
NCP1396 controller:
? Wide frequency range: A high-- speed Voltage
Control Oscillator allows an output frequency
excursion from 50 kHz up to 500 kHz on Mlower and
Mupper outputs.
? Adjustable dead-- time: Thanks to a single resistor
wired to ground, the user has the ability to include
some dead-- time, helping to fight cross-- conduction
between the upper and the lower transistor.
? Adjustable soft-- start: Every time the controller starts
to operate (power on), the switching frequency is
pushed to the programmed maximum value and slowly
moves down toward the minimum frequency, until the
feedback loop closes. The soft-- start sequence is
activated in the following cases: a) normal startup
b) back to operation from an off state: during hiccup
faulty mode, brown-- out or temperature shutdown
(TSD). In the NCP1396A, the soft-- start is not
activated back to operation from the fast fault input,
unless the feedback pin voltage is below 0.6 V. To the
opposite, in the B version, the soft-- start is always
activated back from the fast fault input whatever the
feedback level is.
? Adjustable minimum and maximum frequency
excursion: In resonant applications, it is important to
stay away from the resonating peak to keep operating
the converter in the right region. Thanks to a single
external resistor, the designer can program its lowest
frequency point, obtained in lack of feedback voltage
(during the startup sequence or in short-- circuit
conditions). Internally trimmed capacitors offer a ? 3%
precision on the selection of the minimum switching
frequency. The adjustable upper stop being less
precise to ? 15%.
? Low startup current: When directly powered from
the high-- voltage DC rail, the device only requires
300 m A to start-- up. In case of an auxiliary supply, the
B version offers a lower start-- up threshold to cope
with a 12 V dc rail.
? Brown-- Out detection: To avoid operation from a low
input voltage, it is interesting to prevent the controller
from switching if the high-- voltage rail is not within
the right boundaries. Also, when teamed with a PFC
front-- end circuitry, the brown-- out detection can
ensure a clean start-- up sequence with soft-- start,
ensuring that the PFC is stabilized before energizing
the resonant tank. The A version features a 26.5 m A
hysteresis current for the lowest consumption and the
?
?
?
?
?
?
B version slightly increases this current to 100 m A in
order to improve the noise immunity.
Adjustable fault timer duration: When a fault is
detected on the slow fault input or when the FB path is
broken, a timer starts to charge an external capacitor.
If the fault is removed, the timer opens the charging
path and nothing happens. When the timer reaches its
selected duration (via a capacitor on pin 3), all pulses
are stopped. The controller now waits for the
discharge via an external resistor of pin 3 capacitor to
issue a new clean startup sequence with soft-- start.
Cumulative fault events: In the NCP1396A/B, the
timer capacitor is not reset when the fault disappears.
It actually integrates the information and cumulates
the occurrences. A resistor placed in parallel with the
capacitor will offer a simple way to adjust the
discharge rate and thus the auto-- recovery retry rate.
Fast and slow fault detection: In some application,
subject to heavy load transients, it is interesting to
give a certain time to the fault circuit, before
activating the protection. On the other hands, some
critical faults cannot accept any delay before a
corrective action is taken. For this reason, the
NCP1396A/B includes a fast fault and a slow fault
input. Upon assertion, the fast fault immediately stops
all pulses and stays in the position as long as the
driving signal is high. When released low (the fault
has gone), the controller has several choices: in the A
version, pulses are back to a level imposed by the
feedback pin without soft-- start, but in the B version,
pulses are back through a regular soft-- start sequence.
Skip cycle possibility: The absence of soft-- start on
the NCP1396A fast fault input offers an easy way to
implement skip cycle when power saving features are
necessary. A simple resistive connection from the
feedback pin to the fast fault input, and skip can be
implemented.
Broken feedback loop detection: Upon start-- up or
any time during operation, if the FB signal is missing,
the timer starts to charge a capacitor. If the loop is
really broken, the FB level does not grow-- up before
the timer ends counting. The controller then stops all
pulses and waits that the timer pin voltage collapses to
1 V typically before a new attempt to re-- start, via the
soft-- start. If the optocoupler is permanently broken, a
hiccup takes place.
Finally, two circuit versions, A and B: The A and B
versions differ because of the following changes:
1. The startup thresholds are different, the A starts
to pulse for V CC = 13.3 V whereas the B pulses
for V CC = 10.5 V. The turn off levels are the same
however. The A is recommended for consumer
http://onsemi.com
13
相关PDF资料 |
PDF描述 |
|---|---|
| NCP1397ADR2G | IC REG CTRLR ISO PWM 16-SOIC |
| NCP1417DMR2 | IC REG BST SYNC ADJ 0.2A 8MICRO |
| NCP1421DMR2 | IC REG BST SYNC ADJ 0.6A 8MICRO |
| NCP1450ASN50T1G | IC REG CTRLR BST PWM VM 5TSOP |
| NCP1521BMUTBG | IC REG BUCK SYNC ADJ 0.6A 6UDFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| NCP1396BPG | 功能描述:电压模式 PWM 控制器 RESONANT MODE CNTRLR W/ H/L SIDES DRIVERS RoHS:否 制造商:Texas Instruments 输出端数量:1 拓扑结构:Buck 输出电压:34 V 输出电流: 开关频率: 工作电源电压:4.5 V to 5.5 V 电源电流:600 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 封装 / 箱体:WSON-8 封装:Reel |
| NCP1396D | 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:High Performance Resonant Mode Controller featuring High--Voltage Drivers |
| NCP1397A | 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:High Performance Resonant Mode Controller with Integrated High-Voltage Drivers |
| NCP1397ADR2G | 功能描述:电流型 PWM 控制器 NCP1397A RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| NCP1397B | 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:High Performance Resonant Mode Controller with Integrated High-Voltage Drivers |
发布紧急采购，3分钟左右您将得到回复。