参数资料
| 型号： | NCP1417DMR2 |
| 厂商： | ON Semiconductor |
| 文件页数： | 10/13页 |
| 文件大小： | 0K |
| 描述： | IC REG BST SYNC ADJ 0.2A 8MICRO |
| 产品变化通告： | Product Obsolescence 01/Apr/2004 |
| 标准包装： | 1 |
| 类型： | 升压（升压） |
| 输出类型： | 可调式 |
| 输出数： | 1 |
| 输出电压： | 1.5 V ~ 5.5 V |
| 输入电压： | 1 V ~ 5.5 V |
| 频率 - 开关： | 600kHz |
| 电流 - 输出： | 200mA |
| 同步整流器： | 是 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-TSSOP，8-MSOP（0.118"，3.00mm 宽） |
| 包装： | 剪切带 (CT) |
| 供应商设备封装： | Micro8? |
| 其它名称： | NCP1417DMR2OSCT |
NCP1417
1 ) FB1
VOUT + 1.190 V
higher than 1.190 V + 30 mV, the comparator output will
cause the 50 W low side switch to be turned OFF, pin 3 will
become high impedance, and its voltage will be pulled high.
The second low ? battery detector functions in the same
manner, the second comparator, CP2 with a lower triggering
reference point derived from the internal reference is used
instead, typical 0.944 V. This configuration provides two
levels of low battery warning to the target system.
APPLICATIONS INFORMATION
Output Voltage Setting
The output voltage of the converter is determined by the
external feedback network comprised of R FB1 and R FB2 and
the relationship is given by:
R
RFB2
where R FB1 and R FB2 are the upper and lower feedback
resistors respectively.
Low Battery Detect Level Setting
out of the capacitors multiplying with the Equivalent Series
Resistance (ESR) of the capacitor producing ripple voltage
at the terminals. During the syn ? rect switch off cycle, the
charges stored in the output capacitor is used to sustain the
output load current. Load current at this period and the ESR
combined and reflected as ripple at the output terminal. For
all cases, the lower the capacitor ESR, the lower the ripple
voltage at output. As a general guide line, low ESR
capacitors should be used. Ceramic capacitors have the
lowest ESR, but low ESR tantalum capacitors can also be
used as a cost effective substitute.
Optional Startup Schottky Diode for Low Battery
Voltage
In general operation, no external schottky diode is
required, however, in case you are intended to operate the
device close to 1.0 V level, a schottky diode connected
between the LX and OUT pins as shown in Figure 27 can
help during startup of the converter. The effect of the
additional schottky is shown in Figure 8.
1 ) LB1
The Low Battery Detect Voltages of the converter are
determined by the external divider network comprised of
R LB1 and R LB2 and the relationship is given by:
R
VLB1 + 1.190 V
RLB2
OUT
L
MBR0520
V OUT
where R LB1 and R LB2 are the upper and lower divider
resistors respectively. By setting the V LB1 , the second low
battery detection point, V LB2 will be fixed automatically.
NCP1417
LX
C OUT
Inductor Selection
The NCP1417 is tested to produce optimum performance
with a 22 m H inductor at V IN = 3.0 V, V OUT = 3.3 V
supplying output current up to 200 mA. For other
input/output requirements, inductance in the range 10 m H to
47 m H can be used according to end application
specifications. Selecting an inductor is a compromise
between output current capability and tolerable output
voltage ripple. Of course, the first thing we need to obey is
to keep the peak inductor current below its saturation limit
at maximum current and the I LIM of the device. In NCP1417,
I LIM is set at 1.0 A. As a rule of thumb, low inductance
values supply higher output current, but also increase the
ripple at output and reducing efficiency, on the other hand,
high inductance values can improve output ripple and
efficiency, however it also limit the output current capability
at the same time. One other parameter of the inductor is its
DC resistance, this resistance can introduce unwanted
power loss and hence reduce overall efficiency, the basic
rule is selecting an inductor with lowest DC resistance
within the board space limitation of the end application.
Capacitors Selection
In all switching mode boost converter applications,
both the input and output terminals sees impulsive
voltage/current waveforms. The currents flowing into and
Figure 27.
PCB Layout Recommendations
Good PCB layout plays an important role in switching
mode power conversion. Careful PCB layout can help to
minimize ground bounce, EMI noise and unwanted
feedback that can affect the performance of the converter.
Hints suggested in below can be used as a guide line in most
situations.
Grounding
Star ? ground connection should be used to connect the
output power return ground, the input power return ground
and the device power ground together at one point. All high
current running paths must be thick enough for current
flowing through and producing insignificant voltage drop
along the path. Feedback signal path must be separated with
the main current path and sensing directly at the anode of the
output capacitor.
Components Placement
Power components, i.e. input capacitor, inductor and
output capacitor, must be placed as close together as
possible. All connecting traces must be short, direct and
thick. High current flowing and switching paths must be
http://onsemi.com
10
相关PDF资料 |
PDF描述 |
|---|---|
| NCP1421DMR2 | IC REG BST SYNC ADJ 0.6A 8MICRO |
| NCP1450ASN50T1G | IC REG CTRLR BST PWM VM 5TSOP |
| NCP1521BMUTBG | IC REG BUCK SYNC ADJ 0.6A 6UDFN |
| NCP1522ASNT1G | IC REG BUCK SYNC ADJ 0.6A 5TSOP |
| NCP1522BMUTBG | IC REG BUCK SYNC ADJ 0.6A 6UDFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| NCP1417-SKT | 制造商:ON Semiconductor 功能描述:Sample Kit, Including 2 NCP1417DM2 and 1 Development Resource CD-ROM 制造商:P&S 功能描述:Sample Kit, Including 2 NCP1417DM2 and 1 Development Resource CD-ROM |
| NCP1421DMR2 | 功能描述:直流/直流开关转换器 600mA PFM Boost RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
| NCP1421DMR2G | 功能描述:DC/DC 开关控制器 600mA PFM Boost w/Ring Killer RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| NCP1421EVB | 功能描述:电源管理IC开发工具 ANA NCP1421 EVAL BRD RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| NCP1421LEDEVB | 功能描述:LED 照明开发工具 ANA NCP1421 EVAL BRD RoHS:否 制造商:Fairchild Semiconductor 产品:Evaluation Kits 用于:FL7732 核心: 电源电压:120V 系列: 封装: |
发布紧急采购，3分钟左右您将得到回复。