- 您现在的位置：买卖IC网 > PDF目录15088 > NCP1450ASN33T1 (ON Semiconductor)IC REG CTRLR BST PWM VM 5TSOP PDF资料下载
参数资料
| 型号： | NCP1450ASN33T1 |
| 厂商： | ON Semiconductor |
| 文件页数： | 17/22页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR BST PWM VM 5TSOP |
| 产品变化通告： | LTB Notification 03/Jan/2008 |
| 标准包装： | 1 |
| PWM 型： | 电压模式 |
| 输出数： | 1 |
| 频率 - 最大： | 216kHz |
| 占空比： | 90% |
| 电源电压： | 0.6 V ~ 5.5 V |
| 降压： | 无 |
| 升压： | 是 |
| 回扫： | 无 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 6-TSOP（0.059"，1.50mm 宽）5 引线 |
| 包装： | 剪切带 (CT) |
| 其它名称： | NCP1450ASN33TOSCT |
NCP1450A
DETAILED OPERATING DESCRIPTION
Operation
The NCP1450A series are monolithic power switching
controllers optimized for battery powered portable products
where large output current is required.
The NCP1450A series are low noise fixed frequency
voltage?mode PWM DC?DC controllers, and consist of
startup circuit, feedback resistor divider, reference voltage,
oscillator, loop compensation network, PWM control
circuit, and low ON resistance driver. Due to the on?chip
feedback resistor and loop compensation network, the
system designer can get the regulated output voltage from
1.8 V to 5.0 V with 0.1 V stepwise with a small number of
external components. The quiescent current is typically
93 m A (V OUT = 2.7 V, f OSC = 180 kHz), and can be further
reduced to about 1.5 m A when the chip is disabled (V CE t
0.3 V).
The NCP1450A operation can be best understood by
referring to the block diagram in Figure 2. The error
amplifier monitors the output voltage via the feedback
resistor divider by comparing the feedback voltage with the
reference voltage. When the feedback voltage is lower than
the reference voltage, the error amplifier output will
decrease. The error amplifier output is then compared with
the oscillator ramp voltage at the PWM controller. When the
ramp voltage is higher than the error amplifier output, the
high?side driver is turned on and the low?side driver is
turned off which will then switch on the external transistor;
and vice versa. As the error amplifier output decreases, the
high?side driver turn?on time increases and duty cycle
increases. When the feedback voltage is higher than the
reference voltage, the error amplifier output increases and
the duty cycle decreases. When the external power switch is
on, the current ramps up in the inductor, storing energy in the
magnetic field. When the external power switch is off, the
Soft Start
There is a soft start circuit in NCP1450A. When power is
applied to the device, the soft start circuit first pumps up the
output voltage to approximately 1.5 V at a fixed duty cycle.
This is the voltage level at which the controller can operate
normally. In addition to that, the startup capability with
heavy loads is also improved.
Oscillator
The oscillator frequency is internally set to 180 kHz at an
accuracy of " 20% and with low temperature coefficient of
0.11%/ ° C.
Regulated Converter Voltage (V OUT )
The V OUT is set by an integrated feedback resistor
network. This is trimmed to a selected voltage from 1.8 V to
5.0 V range in 100 mV steps with an accuracy of " 2.5%.
Compensation
The device is designed to operate in continuous
conduction mode. An internal compensation circuit was
designed to guarantee stability over the full input/output
voltage and full output load range.
Enable/Disable Operation
The NCP1450A series offer IC shutdown mode by chip
enable pin (CE pin) to reduce current consumption. When
voltage at pin CE is equal or greater than 0.9 V, the chip will
be enabled, which means the controller is in normal
operation. When voltage at pin CE is less than 0.3 V, the chip
is disabled, which means IC is shutdown.
Important: DO NOT apply a voltage between 0.3 V to 0.9 V
to pin CE as this is the CE pin’s hysteresis voltage range.
Clearly defined output states can only be obtained by
applying voltage out of this range.
energy stored in the magnetic field is transferred to the
output filter capacitor and the load. The output filter
capacitor stores the charge while the inductor current is
higher than the output current, then sustains the output
voltage until the next switching cycle.
As the load current is decreased, the switch transistor turns
on for a shorter duty cycle. Under the light load condition,
the controller will skip switching cycles to reduce power
consumption, so that high efficiency is maintained at light
loads.
http://onsemi.com
17
相关PDF资料 |
PDF描述 |
|---|---|
| X5045S8Z-2.7A | IC CPU SUPERV 4K EEPROM 8-SOIC |
| X5045S8Z-2.7 | IC CPU SUPERV 4K EEPROM 8-SOIC |
| NCP1450ASN30T1 | IC REG CTRLR BST PWM VM 5TSOP |
| RCA32DTKT | CONN EDGECARD 64POS DIP .125 SLD |
| GCM36DTBH | CONN EDGECARD 72POS R/A .156 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| NCP1450ASN33T1G | 功能描述:直流/直流开关转换器 3.3V 1A Boost DC-DC PWM RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
| NCP1450ASN50T1 | 功能描述:直流/直流开关转换器 5V 1A Boost DC-DC RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
| NCP1450ASN50T1G | 功能描述:直流/直流开关转换器 5V 1A Boost DC-DC PWM RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
| NCP1450ASN50T1G | 制造商:ON Semiconductor 功能描述:Power Supply IC |
| NCP1500DMR2 | 功能描述:直流/直流开关转换器 Dual Mode PWM RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
发布紧急采购，3分钟左右您将得到回复。