- 您现在的位置：买卖IC网 > PDF目录17322 > NCP1522BUGEVB (ON Semiconductor)EVAL BOARD FOR NCP1522BU PDF资料下载
参数资料
| 型号： | NCP1522BUGEVB |
| 厂商： | ON Semiconductor |
| 文件页数： | 10/17页 |
| 文件大小： | 0K |
| 描述： | EVAL BOARD FOR NCP1522BU |
| 设计资源： | NCP1522BUEVB BOM NCP1522BUEVB Schematic NCP1522BUEVB Gerber Files |
| 标准包装： | 1 |
| 主要目的： | DC/DC，步降 |
| 输出及类型： | 1，非隔离 |
| 输出电压： | 1.2V |
| 电流 - 输出： | 600mA |
| 输入电压： | 3.6V |
| 稳压器拓扑结构： | 降压 |
| 频率 - 开关： | 3MHz |
| 板类型： | 完全填充 |
| 已供物品： | 板 |
| 已用 IC / 零件： | NCP1522 |
| 其它名称： | NCP1522BUEVB NCP1522BUEVBG NCP1522BUEVBOS NCP1522BUEVBOS-ND NCP1522BUGEVBOS |
NCP1522
Cycle-by-Cycle Current Limitation
From the block diagram (Figure 3), an I LIM comparator
is used to realize cycle-by-cycle current limit protection.
The comparator compares the LX pin voltage with the
reference voltage, which is biased by a constant current. If
the inductor current reaches the limit, the I LIM comparator
detects the LX voltage falling below the reference voltage
and releases the signal to turn off the switch Q1. The
cycle-by-cycle current limit is set at 1200 mA (nom).
Short Circuit Protection
When the output is shorted to ground, the device limits
the inductor current. The duty-cycle is minimum and the
consumption on the input line is 300 mA (Typ). When the
short circuit condition is removed, the device returns to the
normal mode of operation.
Soft-Start
The NCP1522 uses soft-start (300 m s Typ) to limit the
inrush current when the device is initially enabled.
Soft-start is implemented by gradually increasing the
reference voltage until it reaches the full reference voltage.
During startup, a pulsed current source charges the internal
soft-start capacitor to provide gradually increasing
consumption will be 0.3 m A (typical value). Applying a
voltage above 1.2 V to EN pin will enable the device for
normal operation. The device will go through soft-start to
normal operation, however, the EN pin should be tied low
while the input voltage on V IN pin is rising up.
Thermal Shutdown
Internal Thermal Shutdown circuitry is provided to
protect the integrated circuit in the event that the maximum
junction temperature is exceeded. If the junction
temperature exceeds 160 _ C, the device shuts down. In this
mode switch Q1 and Q2 and the control circuits are all
turned off. The device restarts in soft-start after the
temperature drops below 135 _ C. This feature is provided
to prevent catastrophic failures from accidental device
overheating and it is not intended as a substitute for proper
heatsinking.
Low Dropout Operation
The NCP1522 offers a low input to output voltage
difference. The NCP1522 can operate at 100% duty cycle.
In this mode the PMOS (Q1) switches completely on.
The minimum input voltage to maintain regulation can
be calculated as:
reference voltage. When the voltage across the capacitor
ramps up to the nominal reference voltage, the pulsed
current source will be switched off and the reference
voltage will switch to the regular reference voltage.
Shutdown Mode
When the EN pin has a voltage applied of less than 0.4 V,
the NCP1522 will be disabled. In shutdown mode, the
internal reference, oscillator and most of the control
?
?
?
?
VIN(min) + VOUT(max)
) (IOUT (RDS(on) ) RINDUCTOR))
V OUT : Output Voltage (Volts)
I OUT : Max Output Current
R DS(on) : P-Channel Switch R DS(on)
R INDUCTOR : Inductor Resistance (DCR)
(eq. 1)
circuitries are turned off. Therefore, the typical current
http://onsemi.com
10
相关PDF资料 |
PDF描述 |
|---|---|
| RBM11DRTI | CONN EDGECARD 22POS DIP .156 SLD |
| A9CCA-1704E | FLEX CABLE - AFK17A/AE17/AFK17A |
| RCM15DRTH | CONN EDGECARD 30POS DIP .156 SLD |
| SS10P4HM3/87A | DIODE SCHOTTKY 10A 40V SMPC |
| SS10P3HM3/87A | DIODE SCHOTTKY 10A 30V SMPC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| NCP1523BFCT2G | 功能描述:直流/直流开关转换器 FORCED PWM NCP1523 RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
| NCP1523BGEVB | 功能描述:电源管理IC开发工具 NCP1523B EVAL BRD RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| NCP1523FCT2G | 功能描述:直流/直流开关转换器 UBUMP DCDC RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
| NCP1526EVB | 功能描述:电源管理IC开发工具 NCP1526 EVALUATION BOARD RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| NCP1526MUTXG | 功能描述:直流/直流开关转换器 BUCK REG AND LDO RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
发布紧急采购，3分钟左右您将得到回复。