- 您现在的位置：买卖IC网 > PDF目录17398 > NCP1599GEVB (ON Semiconductor)BOARD EVALUATION NCP1599 PDF资料下载
参数资料
| 型号： | NCP1599GEVB |
| 厂商： | ON Semiconductor |
| 文件页数： | 10/15页 |
| 文件大小： | 0K |
| 描述： | BOARD EVALUATION NCP1599 |
| 设计资源： | NCP1599GEVB BOM NCP1599GEVB Schematic NCP1599GEVB Gerber Files |
| 标准包装： | 1 |
| 主要目的： | DC/DC，步降 |
| 输出及类型： | 1，非隔离 |
| 输出电压： | 最低可调至 0.8V |
| 电流 - 输出： | 3A |
| 输入电压： | 3 ~ 5.5 V |
| 稳压器拓扑结构： | 降压 |
| 频率 - 开关： | 1MHz |
| 板类型： | 完全填充 |
| 已供物品： | 板 |
| 已用 IC / 零件： | NCP1599 |
| 其它名称： | NCP1599GEVBOS |
NCP1599
DETAILED DESCRIPTION
Overview
The NCP1599 is a synchronous PWM controller that
incorporates all the control and protection circuitry
necessary to satisfy a wide range of applications. The
NCP1599 employs current mode control to provide good
transient response, simple compensation, and excellent
stability. The features of the NCP1599 include a precision
reference, fixed 1 MHz switching frequency, a
transconductance error amplifier, an integrated high ? side
P ? channel MOSFET and low ? side N ? Channel MOSFET,
internal soft ? start, and very low shutdown current. The
protection features of the NCP1599 include internal
soft ? start, pulse ? by ? pulse current limit, hiccup mode
short ? circuit protection, and thermal shutdown.
Reference Voltage
The NCP1599 incorporates an internal reference that
allows output voltages as low as 0.8 V. The tolerance of the
internal reference is guaranteed over the entire operating
temperature range of the controller. The reference voltage is
trimmed using a test configuration that accounts for error
amplifier offset and bias currents.
Oscillator Frequency
A fixed precision oscillator is provided. The oscillator
frequency range is 1 MHz with ± 13% variation.
Transconductance Error Amplifier
The transconductance error amplifier ’s primary function
is to regulate the converter ’s output voltage using a resistor
divider connected from the converter ’s output to the FB pin
of the controller, as shown in the applications Schematic. A
series RC compensation network must be connected from
the error amplifier’s output (COMP pin) to GND to stabilize
the converter. In some applications, a lower value capacitor
may be connected from the COMP pin to GND to reduce the
loop gain at higher frequencies. However, if this capacitor
is too large the phase margin of the converter will be
reduced. If a Fault occurs, the COMP pin is immediately
pulled to GND and PWM switching is inhibited.
Internal Soft ? Start
To limit the startup inrush current, an internal soft start
circuit is used to ramp up the reference voltage from 0 V to
its final value linearly. The internal soft start time is 1 ms
typically.
Output MOSFETs
The NCP1599 includes low R DS(on) , both high ? side
P ? channel and low ? side N ? channel MOSFETs capable of
delivering up to 3.0 A of current. When the controller is
disabled or during a Fault condition, the controller ’s output
stage is tri ? stated by turning OFF both the upper and lower
MOSFETs.
Adaptive Dead Time Gate Driver
In a synchronous buck converter, a certain dead time is
required between the low side drive signal and high side
drive signal to avoid shoot through. During the dead time,
the body diode of the low side FET freewheels the current.
The body diode has much higher voltage drop than that of
the MOSFET, which reduces the efficiency significantly.
The longer the body diode conducts, the lower the
efficiency. In NCP1599, the drivers and MOSFETs are
integrated in a single chip. The parasitic inductance is
minimized. Adaptive dead time control method is used in
NCP1599 to prevent the shoot through from happening and
minimizing the diode conduction loss at the same time.
Pulse Width Modulation
A high ? speed PWM comparator, capable of pulse widths
as low as 50 ns, is included in the NCP1599. The inverting
input of the comparator is connected to the output of the
error amplifier. The non ? inverting input is connected to the
the current sense signal. At the beginning of each PWM
cycle, the CLK signal sets the PWM flip ? flop and the upper
MOSFET is turned ON. When the current sense signal rises
above the error amplifier’s voltage then the comparator will
reset the PWM flip ? flop and the upper MOSFET will be
turned OFF.
Power Save Mode
If the load current decreases, the converter will enter
power save mode operation automatically. During power
save mode, the converter skips switching and operates with
reduced frequency, which minimizes the quiescent current
and maintain high efficiency.
Current Sense Amplifier
The NCP1599 monitors the current in the upper
MOSFET. The current signal is required by the PWM
comparator, the pulse ? by ? pulse current limiter, and the
hiccup mode/over current counter.
http://onsemi.com
10
相关PDF资料 |
PDF描述 |
|---|---|
| GCC20DCMI-S288 | CONN EDGECARD 40POS .100 EXTEND |
| GEC18DREN-S13 | CONN EDGECARD 36POS .100 EXTEND |
| A9AAT-1608F | FLEX CABLE - AFE16T/AF16/AFE16T |
| GSC06DREH-S13 | CONN EDGECARD 12POS .100 EXTEND |
| A9BAA-1006F | FLEX CABLE - AFF10A/AF10/AFE10T |
相关代理商/技术参数 |
参数描述 |
|---|---|
| NCP1599MNTWG | 功能描述:直流/直流开关转换器 SYNC BUCK CONTROLLER RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
| NCP15WB333E03RC | 制造商:Murata Manufacturing Co Ltd 功能描述:LEADED NTC THERMISTOR |
| NCP15WB333J03RC | 功能描述:热敏电阻 - NTC 33K OHM 5% RoHS:否 制造商:EPCOS 电阻:10 kOhms 功率额定值:150 mW 容差:2 % 端接类型:Radial 系列:B57703M 工作温度范围:- 55 C to + 125 C |
| NCP15WB333K03RC | 功能描述:热敏电阻 - NTC 33K OHM 10% RoHS:否 制造商:EPCOS 电阻:10 kOhms 功率额定值:150 mW 容差:2 % 端接类型:Radial 系列:B57703M 工作温度范围:- 55 C to + 125 C |
| NCP15WB473D03RC | 功能描述:NTC THERMISTOR 47K OHM 0.5% 0402 制造商:murata electronics north america 系列:NCP15 包装:散装 零件状态:在售 25°C 时欧姆阻值:47k 电阻容差:±0.5% B 值容差:±0.5% B0/50:- B25/50:4050K B25/75:- B25/85:4108K B25/100:4131K 工作温度:-40°C ~ 125°C 功率 - 最大值:100mW 长度 - 引线:- 安装类型:表面贴装 封装/外壳:0402（1005 公制） 标准包装:10,000 |
发布紧急采购，3分钟左右您将得到回复。