- 您现在的位置：买卖IC网 > PDF目录22192 > NCP1653AP (ON Semiconductor)IC CTLR PFC CCM COMPACT FF 8DIP PDF资料下载
参数资料
| 型号： | NCP1653AP |
| 厂商： | ON Semiconductor |
| 文件页数： | 3/19页 |
| 文件大小： | 0K |
| 描述： | IC CTLR PFC CCM COMPACT FF 8DIP |
| 产品变化通告： | LTB Notification 03/Jan/2008 |
| 标准包装： | 50 |
| 模式： | 连续导电（CCM） |
| 频率 - 开关： | 60.3kHz ~ 73.7kHz |
| 电源电压： | 8.75 V ~ 18 V |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 通孔 |
| 封装/外壳： | 8-DIP（0.300"，7.62mm） |
| 供应商设备封装： | 8-PDIP |
| 包装： | 管件 |
NCP1653, NCP1653A
PIN FUNCTION DESCRIPTION
Pin
1
Symbol
FB / SD
Name
Feedback /
Shutdown
Function
This pin receives a feedback current I FB which is proportional to the PFC circuit output voltage.
The current is for output regulation, output overvoltage protection (OVP), and output undervoltage
protection (UVP).
When I FB goes above 107% I ref , OVP is activated and the Drive Output is disabled.
When I FB goes below 8% I ref , the device enters a low ? consumption shutdown mode.
2
V control
Control Voltage /
Soft ? Start
The voltage of this pin V control directly controls the input impedance and hence the power factor of
the circuit. This pin is connected to an external capacitor C control to limit the V control bandwidth
typically below 20 Hz to achieve near unity power factor.
The device provides no output when V control = 0 V. Hence, C control also works as a soft ? start
capacitor.
3
4
5
6
7
8
In
CS
V M
GND
Drv
V CC
Input Voltage
Sense
Input Current
Sense
Multiplier
Voltage
The IC Ground
Drive Output
Supply Voltage
This pin sinks an input ? voltage current I vac which is proportional to the RMS input voltage V ac .
The current I vac is for overpower limitation (OPL) and PFC duty cycle modulation. When the
product (I S ? I vac ) goes above 3 nA 2 , OPL is activated and the Drive Output duty ratio is reduced by
pulling down V control indirectly to reduce the input power.
This pin sources a current I S which is proportional to the inductor current I L . The sense current I S
is for overcurrent protection (OCP), overpower limitation (OPL) and PFC duty cycle modulation.
When I S goes above 200 m A, OCP is activated and the Drive Output is disabled.
This pin provides a voltage V M for the PFC duty cycle modulation. The input impedance of the
PFC circuit is proportional to the resistor R M externally connected to this pin. The device operates
in average current ? mode if an external capacitor C M is connected to the pin. Otherwise, it
operates in peak current ? mode.
?
This pin provides an output to an external MOSFET.
This pin is the positive supply of the device. The operating range is between 8.75 V and 18 V with
UVLO start threshold 13.25 V.
MAXIMUM RATINGS
Rating
Symbol
Value
Unit
FB, V control , In, CS, V M Pins (Pins 1 ? 5)
Maximum Voltage Range
Maximum Current
V max
I max
? 0.3 to +9
100
V
mA
Drive Output (Pin 7)
Maximum Voltage Range
Maximum Current Range (Note 1)
V max
I max
? 0.3 to +18
1.5
V
A
Power Supply Voltage (Pin 8)
Maximum Voltage Range
Maximum Current
Transient Power Supply Voltage, Duration < 10 ms, IV CC < 20 mA
V max
I max
? 0.3 to +18
100
25
V
mA
V
Power Dissipation and Thermal Characteristics
P suffix, Plastic Package, Case 626
Maximum Power Dissipation @ T A = 70 ° C
Thermal Resistance Junction ? to ? Air
D suffix, Plastic Package, Case 751
Maximum Power Dissipation @ T A = 70 ° C
Thermal Resistance Junction ? to ? Air
Operating Junction Temperature Range
Storage Temperature Range
P D
R q JA
P D
R q JA
T J
T stg
800
100
450
178
? 40 to +125
? 65 to +150
mW
° C/W
mW
° C/W
° C
° C
Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the
Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect
device reliability.
A. This device series contains ESD protection and exceeds the following tests:
Pins 1 ? 8: Human Body Model 2000 V per MIL ? STD ? 883, Method 3015.
Machine Model Method 190 V.
B. This device contains Latchup protection and exceeds ± 100 mA per JEDEC Standard JESD78.
1. Guaranteed by design.
http://onsemi.com
3
相关PDF资料 |
PDF描述 |
|---|---|
| NCP584HSN15T1G | IC REG LDO 1.5V .2A SOT23-5 |
| RCM10DRSS | CONN EDGECARD 20POS DIP .156 SLD |
| RAC10-05SA | CONV AC/DC 90-264VAC 5V 2A |
| VI-JT2-CX-F2 | CONVERTER MOD DC/DC 15V 75W |
| RCM10DRMS | CONN EDGECARD 20POS .156 WW |
相关代理商/技术参数 |
参数描述 |
|---|---|
| NCP1653APG | 功能描述:功率因数校正 IC Fixed Frequency Current Mode PFC RoHS:否 制造商:Fairchild Semiconductor 开关频率:300 KHz 最大功率耗散: 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Reel |
| NCP1653DR2 | 功能描述:功率因数校正 IC Fixed Frequency RoHS:否 制造商:Fairchild Semiconductor 开关频率:300 KHz 最大功率耗散: 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Reel |
| NCP1653DR2G | 功能描述:功率因数校正 IC Fixed Frequency Current Mode PFC RoHS:否 制造商:Fairchild Semiconductor 开关频率:300 KHz 最大功率耗散: 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Reel |
| NCP1653EVB | 功能描述:BOARD EVAL FOR NCP1653 RoHS:是 类别:编程器，开发系统 >> 评估演示板和套件 系列:- 标准包装:1 系列:PCI Express® (PCIe) 主要目的:接口，收发器，PCI Express 嵌入式:- 已用 IC / 零件:DS80PCI800 主要属性:- 次要属性:- 已供物品:板 |
| NCP1653GEVB | 制造商:ON Semiconductor 功能描述:NCP1653 PFC CCM STEP-UP - Bulk 制造商:ON Semiconductor 功能描述:BOARD EVAL FOR NCP1653 |
发布紧急采购，3分钟左右您将得到回复。