- 您现在的位置：买卖IC网 > PDF目录17138 > NCP1800DM41R2G (ON Semiconductor)IC CTRLR BATT CHRGR CC/CV 8MICRO PDF资料下载
参数资料
| 型号： | NCP1800DM41R2G |
| 厂商： | ON Semiconductor |
| 文件页数： | 12/14页 |
| 文件大小： | 0K |
| 描述： | IC CTRLR BATT CHRGR CC/CV 8MICRO |
| 产品变化通告： | Product Obsolescence 01/Jul/2009 |
| 标准包装： | 1 |
| 功能： | 充电管理 |
| 电池化学： | 锂离子（Li-Ion） |
| 电源电压： | 2.5 V ~ 16 V |
| 工作温度： | -20°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-TSSOP，8-MSOP（0.118"，3.00mm 宽） |
| 供应商设备封装： | Micro8? |
| 包装： | 剪切带 (CT) |
| 其它名称： | NCP1800DM41R2GOSCT |
NCP1800
Selecting External Components
External Adaptor Power Supply Voltage Selection
Since the NCP1800 is using a linear, charging algorithm,
the efficiency is lower. Adapter voltage selection must be
done carefully in order to minimize the heat dissipation. In
general, the power supply input voltage should be around
5.0 to 6.0 V. The minimum input voltage should be chosen
to minimize the heat dissipation in the system. Excessively
high input voltages can cause too much heat dissipation and
will complicate the thermal design in applications like
cellular phones. With the overvoltage protection feature of
the NCP1800, input voltages higher than 7.0 V will activate
the overvoltage protection circuit and disconnect the power
supply input to the battery and other circuitry.
For the application shown in Figure 18 (assuming
NTGS3441 and MBRM130L):
VIN(min) u Li?ion regulated voltage,
VREG ) (0.6 A)(RDS(ON))
) VF of Schottky Diode ) voltage drop of RSNS
u 4.2 V ) (0.6 A) (100 m W ) ) 0.38 V
) (0.6 A) (0.4 W ) + 4.88 V ] 4.9 V
Therefore, for the application shown in Figure 17
(assuming NTHD4P01FT1):
VIN(min) u Li?ion regulated voltage
u 4.2 V ) (0.12 A)(130m W ) ) 0.43
) (0.12 A)(2.0 W ) + 4.89 V ] 4.9 V
If the output voltage accuracy is 5%, then a typ. 5.2 V
5% output voltage adaptor must be used.
And for a very good regulated adaptor of accuracy 1%,
5.0 V ± 1% output voltage adaptor can then be used. It is
obvious that if tighter tolerance adaptors are used, heat
dissipation can be minimized by using lower nominal
voltage adaptors.
Pass Element Selection
The type and size of the pass transistor is determined by
input?output differential voltage, charging current, current
sense resistor and the type of blocking diode used.
The selected pass element must satisfy the following
criteria:
Drop across pass element =
With:
VIN(min) + 5.0 V
VREG + 4.2 V
IREG + 0.6 A
RSNS + 0.4 W
Dropout across pass element =
5.0 V * 4.2 V * 0.38 V * (0.6 A) (0.4 W ) + 0.18 V
Maximum R DS(on) should be less than (0.18 V)/(0.6 A) =
0.3 W at 0.6 A.
VIN(min) + 5.0 V
VREG + 4.2 V
IREG + 0.12 A
RSNS + 2.0 W
Dropout across pass element = 5.0 V ? 4.2 V ? 0.43 V ?
(0.12)(2.0 W) = 0.13 V .
Therefore, maximum R DS(on) should be less than
(0.13 V)/(0.12 A) = 1.08 W at 0.12 A.
External Output Capacitor
Any good quality output filter can be used, independent of
the capacitor ’s minimum ESR. However, a 10 m F tantalum
capacitor or electrolytic capacitor is recommended at the
output to suppress fast ramping spikes at the V SNS input and
to ensure stability for 1.0 A at full range. The capacitor
should be mounted with the shortest possible lead or track
length to the VSNS and GND pins.
Current Sense Resistor
The charging current can be set by the value of the current
sense resistor as in the previous formula. Proper de?rating
is advised when selecting the power dissipation rating of the
resistor. If necessary, R ISEL can also be changed for proper
selection of the R SNS values. Take note of the recommended
full?charge current ranges specified in the electrical
characteristics section. Also notice the effect of RISEL on
the accuracy of pre?charge current and end?of?charge
detection as noted in Figures 10 and 12, respectively.
VIN(min) * Li?ion regulated voltage * VF * IREG
RSNS
http://onsemi.com
12
相关PDF资料 |
PDF描述 |
|---|---|
| NC-165051-25-9 | LABEL ID PRODUCT |
| MRJ0500DF-A | C/A MRJ21/MRJ21 GBE ANGL CMR 50M |
| MRJ0480DD-A | C/A MRJ21/MRJ21 GBE STRT CMR 48M |
| NC-191064-10-9 | LABEL NYLON CLOTH 19.1X0.64MM |
| HL021R0BTTR | INDUCTOR 1NH 346MA 0402 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| NCP1800DM42R2 | 功能描述:电池管理 4.2V Single Cell RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel |
| NCP1800DM42R2G | 功能描述:电池管理 4.2V Single Cell Lithium-Ion Charger RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel |
| NCP1835 AG41 WAF | 制造商:ON Semiconductor 功能描述: |
| NCP1835BMNR2 | 功能描述:电池管理 300mA Max 1 Cell RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel |
| NCP1835BMNR2G | 功能描述:电池管理 300mA Max 1 Cell Lithium-Ion Charger RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。