- 您现在的位置：买卖IC网 > PDF目录18904 > NCP18XW153J03RB (Murata Electronics North America)THERMISTOR 15K OHM NTC 0603 SMD PDF资料下载
参数资料
| 型号： | NCP18XW153J03RB |
| 厂商： | Murata Electronics North America |
| 文件页数： | 33/44页 |
| 文件大小： | 0K |
| 描述： | THERMISTOR 15K OHM NTC 0603 SMD |
| 产品培训模块： | NTC Thermistors and Simulator |
| 产品目录绘图： | NCP Series Side |
| 标准包装： | 1 |
| 系列： | NCP18 |
| 在 25°C 时的电阻（欧姆）： | 15k |
| 电阻公差： | ±5% |
| B 值公差： | ±3% |
| B25/50： | 3950K |
| B25/85： | 3987K |
| B25/100： | 3998K |
| 工作温度： | -40°C ~ 125°C |
| 功率 - 最大： | 100mW |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 0603（1608 公制） |
| 包装： | 标准包装 |
| 产品目录页面： | 2830 (CN2011-ZH PDF) |
| 其它名称： | 490-2444-6 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页当前第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页
! Note ? Please read rating and ! CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
? This catalog has only typical speci?cations. Therefore, please approve our product speci?cations or transact the approval sheet for product speci?cations before ordering.
R44E.pdf
Dec.17,2012
Temperature Sensor Thermo String/Lead Type ! Caution/Notice
c ! Caution (Storage and Operating Conditions)
This product is designed for application in an
ordinary environment (normal room temperature,
humidity and atmospheric pressure).
Do not use under the following conditions because
all of these factors can deteriorate the product
characteristics or cause failures and burn-out.
1. Corrosive gas or deoxidizing gas
(Chlorine gas, Hydrogen sul?de gas, Ammonia gas,
Sulfuric acid gas, Nitric oxide gas, etc.)
c ! Caution (Others)
Be sure to provide an appropriate fail-safe function
on your product to prevent secondary damages that may be
c Notice (Storage and Operating Conditions)
To keep solderability of product from declining, the
following storage condition is recommended.
1. Storage condition:
Temperature -10 to +40 degrees C
Humidity less than 75%RH (not dewing condition)
2. Storage term:
Use this product within 6 months after delivery by
?rst-in and ?rst-out stocking system.
c Notice (Rating)
Use this product within the speci?ed temperature
range.
c Notice (Soldering and Mounting) NXF Series
Please note as shown below when you mount this product.
1. Do not melt solder in the resin head when you solder
this product. If you do so, it has a possibility of wire break,
electric short mode failure and wire coating break.
In case you cut the lead wire of this product less than
20mm from the resin head, the heat of the melted solder
at the lead wire edge is propagated easily to the resin
head along the lead wire.
2. Do not touch the resin head directly with the soldering
iron. It may cause the melting of solder in the resin head.
c Notice (Soldering and Mounting) NXR Series
Please notice as shown below when you mount this product.
1. Do not melt the solder in resin head, when you solder
this product. If you melt the solder in resin head,
it has posibility that the break of wire and short.
In case you cut the lead wire of this product less
than 8mm from resin head, the heat of melted solder
at lead wire edge is propagated easily to the resin
c Notice (Handling)
1. The ceramic element of this product is fragile, and
care must be taken not to load an excessive
press-force or not to give a shock at handling.
Such forces may cause cracking or chipping.
2. Volatile or ?ammable gas
3. Dusty conditions
4. Under vacuum, or under high or low pressure
5. Wet or humid locations
6. Places with salt water, oils, chemical liquids or
organic solvents
7. Strong vibrations
8. Other places where similar hazardous conditions
exist
caused by the abnormal function or the failure of our
product.
3. Handling after unpacking:
After unpacking, reseal product promptly or
store it in a sealed container with a drying agent.
4. Storage place:
Do not store this product in corrosive gas
(Sulfuric acid gas, Chlorine gas, etc.) or in direct
sunlight.
Higher temperature may cause deterioration of the
characteristics or the material quality of this product.
3. Do not separate the parallel lead wires 10mm or less
from the resin head, when you separate parallel lead
wires.
4. If you mold this product by resin, please evaluate
the quality of this product before you use it.
5. Do not bend the lead wire radius 1mm or less when
you bend the lead wire.
head along the lead wire. Please do not cut below
this product 9mm.
2. Do not touch the resin head directly by solder iron.
It may cause the melt of solder in resin head.
3. If you mold by resin this product, please evaluate
the qualityl of this product before you use it.
2. Do not apply an excessive force to the lead.
Otherwise, it may cause junction between lead and
element to break or crack. Holding element by side
lead wire is recommended when lead wire is bent or
cut.
31
相关PDF资料 |
PDF描述 |
|---|---|
| 556-1909-314F | LED 1" ORG PMI 230V CLR FLAT LEN |
| 556-1607-314F | LED 1" GRN PMI 125V CLR FLAT LEN |
| 556-1607-304F | LED 1" FLAT GREEN PMI 125VDC |
| 556-3704-304 | LED PNL MT 1" 24V WT DOME YEL |
| RL3004-144-95-D1 | THERMISTOR NTC DISK 250OHM 25C |
相关代理商/技术参数 |
参数描述 |
|---|---|
| NCP18XW153K03RB | 功能描述:热敏电阻 - NTC 15K OHM 10% RoHS:否 制造商:EPCOS 电阻:10 kOhms 功率额定值:150 mW 容差:2 % 端接类型:Radial 系列:B57703M 工作温度范围:- 55 C to + 125 C |
| NCP18XW222E03RB | 功能描述:热敏电阻 - NTC 2.2K OHM RoHS:否 制造商:EPCOS 电阻:10 kOhms 功率额定值:150 mW 容差:2 % 端接类型:Radial 系列:B57703M 工作温度范围:- 55 C to + 125 C |
| NCP18XW222J03RB | 功能描述:热敏电阻 - NTC 2.2K OHM 5% RoHS:否 制造商:EPCOS 电阻:10 kOhms 功率额定值:150 mW 容差:2 % 端接类型:Radial 系列:B57703M 工作温度范围:- 55 C to + 125 C |
| NCP18XW222K03RB | 功能描述:热敏电阻 - NTC 2.2K OHM 10% RoHS:否 制造商:EPCOS 电阻:10 kOhms 功率额定值:150 mW 容差:2 % 端接类型:Radial 系列:B57703M 工作温度范围:- 55 C to + 125 C |
| NCP18XW223E03RB | 功能描述:热敏电阻 - NTC 22K OHM RoHS:否 制造商:EPCOS 电阻:10 kOhms 功率额定值:150 mW 容差:2 % 端接类型:Radial 系列:B57703M 工作温度范围:- 55 C to + 125 C |
发布紧急采购，3分钟左右您将得到回复。