参数资料
型号: NCP21WB333J03RA
厂商: Murata Electronics North America
文件页数: 31/44页
文件大小: 0K
描述: THERMISTOR 33K OHM NTC 0805 SMD
产品培训模块: NTC Thermistors and Simulator
产品目录绘图: NCP Series Side
标准包装: 1
系列: NCP21
在 25°C 时的电阻(欧姆): 33k
电阻公差: ±5%
B 值公差: ±3%
B25/50: 4050K
B25/85: 4108K
B25/100: 4131K
工作温度: -40°C ~ 125°C
功率 - 最大: 200mW
安装类型: 表面贴装
封装/外壳: 0805(2012 公制)
包装: 标准包装
产品目录页面: 2830 (CN2011-ZH PDF)
其它名称: 490-2449-6
! Note ? Please read rating and ! CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
? This catalog has only typical speci?cations. Therefore, please approve our product speci?cations or transact the approval sheet for product speci?cations before ordering.
R44E.pdf
Dec.17,2012
Temperature Sensor Lead Type Speci?cations and Test Methods
No.
1
2
3
4
5
Item
Low Temperature
Storage Test
High Temperature
Storage Test
High Temperature
Load
Humidity Storage
Test
Temperature
Cycle
Specifications
· Resistance (R25°C) fluctuation rate: less than ±1%.
· B-Constant (B25/50°C) fluctuation rate: less than ±1%.
· Resistance (R25°C) fluctuation rate: less than ±2%.
· B-Constant (B25/50°C) fluctuation rate: less than ±1%.
Test Methods
-40 +0/-3°C in air, for 1000 +48/-0 hours without loading.
125±2°C in air, for 1000 +48/-0 hours without loading.
85±2°C in air, with ‘Operating Current for Sensor’ for
1000 +48/-0 hrs.
60±2°C, 90 to 95%RH in air, for 1000 +48/-0 hours without
loading.
-40°C +0/-3°C, 30 minutes in air
+25°C±2°C, 10 to 15 minutes in air
+125°C +3/-0°C, 30 minutes in air
+25°C +2/-0°C, 10 to 15 minutes in air (1 cycle)
Continuous 100 cycles, without loading.
6
Insulation Break -
down Voltage
· No damage electrical characteristics on D.C.100 V, 1 min.
2mm length of coating resin from the top of thermistor is to be
dipped into beads of lead (Pb), and DC100V 1 minute is
applied to circuit between beads of lead (Pb) and lead wire.
Both lead wires are dipped into 350±10°C solder for 3.5±0.5
seconds, or 260±5°C solder for 10±1 seconds according to
Fig-1. (solder <Sn-3Ag-0.5Cu>)
7
Resistance to
Soldering Heat
· Resistance (R25°C) fluctuation rate: less than ±1%.
· B-Constant (B25/50°C) fluctuation rate: less than ±1%.
Solder
Fig-1
Both lead wires are dipped into flux (25wt% colophony
8
Solder Ability
· More than 90% of lead wire surface shall be covered by
solder.
<JIS K 5902> isopropyl alcohol <JIS K 8839>) for 5 to 10
seconds. Then both lead wires are dipped into 245±5°C solder
<Sn-3Ag-0.5Cu> for 2±0.5 seconds according to Fig-1.
One end of a lead wire shall be fixed and 2.5N forth for 10
seconds shall be applied to the other lead wire as shown in
Fig-2.
6
9
Lead Wire Pull
Strength
· Resistance(R25°C) fluctuation rate: less than ±1%.
· B-Constant(B25/50°C) fluctuation rate: less than ±1%.
· No visible damage at resin part.
2.5N (10sec.)
Fig-2
One lead wire is held and 2.5N force is applied. Then the body
of NTC thermistor is bent by 90°C and again bent back to the
initial position. This sequence shall be completed twice. See
Fig-3.
10
Lead Wire
Bending Strength
· Lead wire does not break.
90°
2.5N
Fig-3
11 Free Fall
· Resistance (R25°C) fluctuation rate: less than ±1%.
NTC thermistor shall be dropped without any force onto
concrete floor from 1 meter height one time.
· B-Constant (B25/50°C) fluctuation rate: less than ±1%.
NTC thermistor shall be fixed to the vibration test Equipment.
12 Vibration
· No visible damage at resin part.
Vibration of total 1.5mm amplitude, Frequency sequence of
10Hz – 55Hz – 10Hz in 1 minute, shall be applied for right
angled 3 directions for each 2 hours duration.
* · R25 is zero-power resistance at 25°C.
· B25/50 is calculated by zero-power resistance of Thermistor in 25°C-50°C.
· After each test, NTC Thermistor should be kept for 1 hour at room temperature (normal humidity and normal atmospheric pressure).
29
相关PDF资料
PDF描述
556-1506-324F LED 1" FLAT RED PMI 72 VDC C1D2
D3V-6G4-1C24-T-K SWITCH LEVER 6A SPDT .187 QC
556-1608-314F LED 1" GRN PMI 37V CLR FLAT LEN
607-1112-310F 7 MM RED PMI W GASKET
NCP21WB473J03RA THERMISTOR 47K OHM NTC 0805 SMD
相关代理商/技术参数
参数描述
NCP21WB333K03RA 功能描述:热敏电阻 - NTC 33K OHM 10% RoHS:否 制造商:EPCOS 电阻:10 kOhms 功率额定值:150 mW 容差:2 % 端接类型:Radial 系列:B57703M 工作温度范围:- 55 C to + 125 C
NCP21WB473 制造商:MURATA 制造商全称:Murata Manufacturing Co., Ltd. 功能描述:for Surface Mounting Application
NCP21WB473J03RA 功能描述:热敏电阻 - NTC 47K OHM 5% RoHS:否 制造商:EPCOS 电阻:10 kOhms 功率额定值:150 mW 容差:2 % 端接类型:Radial 系列:B57703M 工作温度范围:- 55 C to + 125 C
NCP21WB473K03RA 功能描述:热敏电阻 - NTC 47K OHM 10% RoHS:否 制造商:EPCOS 电阻:10 kOhms 功率额定值:150 mW 容差:2 % 端接类型:Radial 系列:B57703M 工作温度范围:- 55 C to + 125 C
NCP21WD683J03RA 制造商:Murata Manufacturing Co Ltd 功能描述:LEADED NTC THERMISTOR