- 您现在的位置：买卖IC网 > PDF目录20456 > NCP3020AGEVB (ON Semiconductor)BOARD EVAL NCP3020A BUCK CTLR PDF资料下载
参数资料
| 型号： | NCP3020AGEVB |
| 厂商： | ON Semiconductor |
| 文件页数： | 12/23页 |
| 文件大小： | 0K |
| 描述： | BOARD EVAL NCP3020A BUCK CTLR |
| 设计资源： | NCP3020AGEVB Schematic NCP3020AGEVB Gerber Files NCP3020AGEVB Bill of Materials |
| 标准包装： | 1 |
| 主要目的： | DC/DC，步降 |
| 输出及类型： | 1，非隔离 |
| 输出电压： | 3.3V |
| 电流 - 输出： | 10A |
| 输入电压： | 9 ~ 18 V |
| 稳压器拓扑结构： | 降压 |
| 频率 - 开关： | 300kHz |
| 板类型： | 完全填充 |
| 已用 IC / 零件： | NCP3020A |
| 其它名称： | NCP3020AGEVB-ND NCP3020AGEVBOS |
NCP3020A, NCP3020B, NCV3020A, NCV3020B
CURRENT LIMIT AND CURRENT LIMIT SET
Overview
The NCP3020 uses the voltage drop across the High Side
MOSFET during the on time to sense inductor current. The
I Limit block consists of a voltage comparator circuit which
compares the differential voltage across the V CC Pin and the
V SW Pin with a resistor settable voltage reference. The sense
portion of the circuit is only active while the HS MOSFET
is turned ON.
VI N
VCC
CONTROL
6
Ilim Out
DAC /
COUNTER
VSense
Itrip Ref
Switch
Cap
Iset
13 uA
Vset
HSDR
VSW
LSDR
RSet
Itrip Ref ? 63 Steps, 6.51 mV/step
Figure 26. I set / I Limit Block Diagram
Current Limit Set
The I Limit comparator reference is set during the startup
sequence by forcing a typically 13 m A current through the
low side gate drive resistor. The gate drive output will rise
to a voltage level shown in the equation below:
V set + I set * R set (eq. 1)
Where I SET is 13 m A and R SET is the gate to source resistor
on the low side MOSFET.
This resistor is normally installed to prevent MOSFET
leakage from causing unwanted turn on of the low side
MOSFET. In this case, the resistor is also used to set the
I Limit trip level reference through the I Limit DAC. The I set
process takes approximately 350 m s to complete prior to
Soft ? Start stepping. The scaled voltage level across the I SET
resistor is converted to a 6 bit digital value and stored as the
trip value. The binary I Limit value is scaled and converted to
the analog I Limit reference voltage through a DAC counter.
The DAC has 63 steps in 6.51 mV increments equating to a
maximum sense voltage of 403 mV. During the I set period
prior to Soft ? Start, the DAC counter increments the
reference on the I SET comparator until it crosses the V SET
voltage and holds the DAC reference output to that count
value. This voltage is translated to the I Limit comparator
during the I Sense portion of the switching cycle through the
switch cap circuit. See Figure 26. Exceeding the maximum
sense voltage results in no current limit. Steps 0 to 10 result
in an effective current limit of 0 mV.
Current Sense Cycle
Figure 27 shows how the current is sampled as it relates
to the switching cycle. Current level 1 in Figure 27
represents a condition that will not cause a fault. Current
level 2 represents a condition that will cause a fault. The
sense circuit is allowed to operate below the 3/4 point of a
given switching cycle. A given switching cycle’s 3/4 T on
time is defined by the prior cycle’s T on and is quantized in
10 ns steps. A fault occurs if the sensed MOSFET voltage
exceeds the DAC reference within the 3/4 time window of
the switching cycle.
http://onsemi.com
12
相关PDF资料 |
PDF描述 |
|---|---|
| GBB06DHLR | CONN EDGECARD 12POS .050 DIP SLD |
| R-782.5-1.0 | CONV DC/DC 1A 2.5V OUT SIP VERT |
| RBC13DCMN-S288 | CONN EDGECARD 26POS .100 EXTEND |
| GSM12DRSN-S288 | CONN EDGECARD 24POS .156 EXTEND |
| RBC13DCMH-S288 | CONN EDGECARD 26POS .100 EXTEND |
相关代理商/技术参数 |
参数描述 |
|---|---|
| NCP3020B | 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:Synchronous PWM Controller |
| NCP3020BDR2G | 功能描述:软开关 PWM 控制器 SYNC PWM CNTRL RoHS:否 制造商:Fairchild Semiconductor 输出端数量: 输出电流: 开关频率: 工作电源电压:30 V 电源电流: 最大工作温度:+ 105 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Reel |
| NCP3020BGEVB | 功能描述:电源管理IC开发工具 NCP3020A EVALUATION BOARD RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| NCP302HSN09T1 | 功能描述:电压监测器/监控器 0.9V Detector RoHS:否 制造商:Texas Instruments 监测电压数:2 监测电压:Adjustable 输出类型:Open Drain 欠电压阈值: 过电压阈值: 准确性:1 % 工作电源电压:1.5 V to 6.5 V 工作电源电流:1.8 uA 最大工作温度:+ 125 C 封装 / 箱体:SON-6 安装风格:SMD/SMT |
| NCP302HSN09T1G | 功能描述:电压监测器/监控器 0.9V Detector w/Reset Hgh RoHS:否 制造商:Texas Instruments 监测电压数:2 监测电压:Adjustable 输出类型:Open Drain 欠电压阈值: 过电压阈值: 准确性:1 % 工作电源电压:1.5 V to 6.5 V 工作电源电流:1.8 uA 最大工作温度:+ 125 C 封装 / 箱体:SON-6 安装风格:SMD/SMT |
发布紧急采购，3分钟左右您将得到回复。