- 您现在的位置：买卖IC网 > Datasheet目录45 > NCP380HMU21AATBG (ON Semiconductor)IC CURRENT LIMIT SWITCH 6-UDFN Datasheet资料下载
参数资料
| 型号： | NCP380HMU21AATBG |
| 厂商： | ON Semiconductor |
| 文件页数： | 15/23页 |
| 文件大小： | 622K |
| 描述： | IC CURRENT LIMIT SWITCH 6-UDFN |
| 标准包装： | 3,000 |
| 功能： | 限流 |
| 检测方法： | 高端 |
| 输入电压： | 2.5 V ~ 5.5 V |
| 电流 - 输出： | 2.1A |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 6-UDFN 裸露焊盘 |
| 供应商设备封装： | 6-uDFN（2x2） |
| 包装： | 带卷 (TR) |
NCP380, NCV380
http://onsemi.com
15
FUNCTIONAL DESCRIPTION
Overview
The NCP380 is a high side P channel MOSFET power
distribution switch designed to protect the input supply
voltage in case of heavy capacitive loads, short circuit or
over current. In addition, the high side MOSFET is turned
off during under voltage, thermal shutdown or reverse
voltage condition. Adjustable version allows the user to
program the current limit threshold using an external
resistor. Thanks to the soft start circuitry, NCP380 is able to
limit large current and voltage surges.
Overcurrent Protection
NCP380 switches into a constant current regulation mode
when the output current is above the I
OCP
threshold.
Depending on the load, the output voltage is decreased
accordingly.
?SPAN class="pst NCP380HMU21AATBG_2471029_4"> In case of hot plug with heavy capacitive load, the
output voltage is brought down to the capacitor voltage.
The NCP380 will limit the current to the I
OCP
threshold
value until the charge of the capacitor is completed.
Figure 22. Heavy capacitive load
V
OUT
I
OUT
Drop due to
Capacitor Charge
I
OCP
?SPAN class="pst NCP380HMU21AATBG_2471029_4"> In case of overload, the current is limited to the I
OCP
value and the voltage value is reduced according to the
load by the following relation:
V
OUT
+ R
LOAD
I
OCP
(eq. 1)
Figure 23. Overload
I
OUT
V
OUT
I
OCP
?R
LOAD
I
OCP
?SPAN class="pst NCP380HMU21AATBG_2471029_4"> In case of short circuit or huge load, the current is
limited to the I
OCP
value within T
DET
time until the
short condition is removed. If the output remains
shorted or tied to a very low voltage, the junction
temperature of the chip exceeds T
SDOCP
value and the
device enters in thermal shutdown (MOSFET is
turned-off).
Figure 24. Short circuit
V
OUT
Thermal
Regulation
Threshold
Timer
Regulation
Mode
I
OUT
I
OCP
T
OCP
T
REG
Then, the device enters in timer regulation mode, described
in 2 phases:
?SPAN class="pst NCP380HMU21AATBG_2471029_4"> Off-phase: Power MOSFET is off during T
OCP
to allow
the die temperature to drop.
?SPAN class="pst NCP380HMU21AATBG_2471029_4"> On-phase: regulation current mode during T
REG.
The
current is regulated to the I
OCP
level.
The timer regulation mode allows the device to handle
high thermal dissipation (in case of short circuit for
example) within temperature operating condition.
NCP380 stays in on-phase/off-phase loop until the over
current condition is removed or enable pin is toggled.
Remark: Other regulation modes can be available for
different applications. Please contact our
ON Semiconductor representative for availability.
FLAG
Indicator
The FLAG
pin is an open-drain MOSFET asserted low
during over current, reverse-voltage or over temperature
conditions. When an over current or a reverse voltage fault
is detected on the power path, FLAG
pin is asserted low at
the end of the associate deglitch time (see electrical
characteristics). Thanks to this feature, the FLAG
pin is not
tied low during the charge of a heavy capacitive load or a
voltage transient on output. Deglitch time is T
FOCP
for over
current fault and T
REV
for reverse voltage. The FLAG
pin
remains low until the fault is removed. Then, the FLAG
pin
goes high at the end of T
FGL
.
Undervoltage Lock-out
Thanks to a built-in under voltage lockout (UVLO)
circuitry, the output remains disconnected from input until
V
IN
voltage is below V
UVLO
. When V
IN
voltage is above
V
UVLO
, the system try to reconnect the output after a
rearming time. T
RUVLO
. This circuit has a V
HYST
hysteresis
witch provides noise immunity to transient.
Thermal Sense
Thermal shutdown turns off the power MOSFET if the die
temperature exceeds T
SD
. A Hysteresis prevents the part
from turning on until the die temperature cools at T
RSD.
相关PDF资料 |
PDF描述 |
|---|---|
| NCT1008DMT3R2G | TMP DIO MON/SMBUS 4CH 8WDFN |
| NCT210RQR2G | IC TEMP SENSOR LOC/REM 16QSOP |
| NCT214MT3R2G | IC TEMP SENSOR LOC/REM 10WDFN |
| NCT72CMNR2G | IC REMOTE THERMAL SENSOR 8-DFN |
| NCT7491RQR2G | IC REMOTE THERMAL MONITOR 24QSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| NCP380HMUAJAATBG | 功能描述:电源开关 IC - 配电 OVER CURRENT PROTECTION RoHS:否 制造商:Exar 输出端数量:1 开启电阻（最大值）:85 mOhms 开启时间（最大值）:400 us 关闭时间（最大值）:20 us 工作电源电压:3.2 V to 6.5 V 电源电流（最大值）: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOT-23-5 |
| NCP380HMUAJAGEVB | 功能描述:电源管理IC开发工具 NCP380 EVAL BOARD RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| NCP380HSN05AAT1G | 功能描述:电源开关 IC - 配电 OVER CURRENT PROTECTION RoHS:否 制造商:Exar 输出端数量:1 开启电阻（最大值）:85 mOhms 开启时间（最大值）:400 us 关闭时间（最大值）:20 us 工作电源电压:3.2 V to 6.5 V 电源电流（最大值）: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOT-23-5 |
| NCP380HSN05AAT2G | 制造商:ON Semiconductor 功能描述:REEL / NCP380 0.5A TSOP5 T2 T&R |
| NCP380HSN05AGEVB | 功能描述:电源管理IC开发工具 NCP380 EVAL BOARD RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
发布紧急采购，3分钟左右您将得到回复。