- 您现在的位置：买卖IC网 > PDF目录22181 > NCP4586DSQ30T1G (ON Semiconductor)IC REG LDO 3V .15A SC82AB PDF资料下载
参数资料
| 型号： | NCP4586DSQ30T1G |
| 厂商： | ON Semiconductor |
| 文件页数： | 14/18页 |
| 文件大小： | 0K |
| 描述： | IC REG LDO 3V .15A SC82AB |
| 标准包装： | 3,000 |
| 稳压器拓扑结构： | 正，固定式 |
| 输出电压： | 3V |
| 输入电压： | 最高 6.5V |
| 电压 - 压降（标准）： | 0.32V @ 150mA |
| 稳压器数量： | 1 |
| 电流 - 输出： | 150mA（最小） |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | SC-82A，SOT-343 |
| 供应商设备封装： | SC-82AB |
| 包装： | 带卷 (TR) |
NCP4586
APPLICATION INFORMATION
A typical application circuit for NCP4586 series is shown
in Figure 42.
version of IC. Active high or low versions are available;
please see the ordering information table. The Enable pin
VIN
C1
470n
NCP4586x
VIN VOUT
CE
GND
VOUT
C2
470n
has an internal pull down current source for versions H and
D. If the enable function is not needed connect the CE pin to
ground for version L or connect the CE pin to VIN for
versions H and D.
Output Discharger
The D version includes a transistor between VOUT and
GND that is used for faster discharging of the output
capacitor. This function is activated when the IC goes into
disable mode.
Figure 42. Typical Application Schematic
Input Decoupling Capacitor (C1)
A 470 nF ceramic input decoupling capacitor should be
connected as close as possible to the input and ground pin of
the NCP4586. Higher values and lower ESR improves line
transient response.
Output Decoupling Capacitor (C2)
A 470 nF or larger ceramic output decoupling capacitor is
sufficient to achieve stable operation of the IC. If a tantalum
capacitor is used, and its ESR is high, loop oscillation may
result. The capacitors should be connected as close as
possible to the output and ground pins. Larger values and
lower ESR improves dynamic parameters.
Thermal
As power across the IC increases, it might become
necessary to provide some thermal relief. The maximum
power dissipation supported by the device is dependent
upon board design and layout. Mounting pad configuration
on the PCB, the board material, and also the ambient
temperature affect the rate of temperature rise for the part.
That is to say, when the device has good thermal
conductivity through the PCB, the junction temperature will
be relatively low with high power dissipation applications.
PCB Layout
Make VIN and GND line sufficient. If their impedance is
high, noise pickup or unstable operation may result. Connect
capacitors C1 and C2 as close as possible to the IC, and make
wiring as short as possible.
Enable Operation
The Enable pin CE or CE may be used for turning the
regulator on and off. Control polarity is dependent on
http://onsemi.com
14
相关PDF资料 |
PDF描述 |
|---|---|
| TAJB225K035RNJ | CAP TANT 2.2UF 35V 10% 1210 |
| RAC15-05DB | CONV AC/DC 2A 6.5-18VIN 3.0-5.5V |
| AD8436ARQZ-R7 | IC CONV TRUE RMS-DC LP 20QSOP |
| SRR6603-331ML | INDUCTOR POWER 330UH SMD |
| AD8436ARQZ-RL | IC CONV TRUE RMS-DC LP 20QSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| NCP4586DSQ33T1G | 功能描述:低压差稳压器 - LDO RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| NCP4586DSQ50T1G | 功能描述:低压差稳压器 - LDO RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| NCP4586SN2.5T1RT | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Analog IC |
| NCP4586SN2.5T1TR | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Analog IC |
| NCP4586SN2.7T1RT | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Analog IC |
发布紧急采购，3分钟左右您将得到回复。