参数资料
| 型号： | NCP512SQ33T2G |
| 厂商： | ON Semiconductor |
| 文件页数： | 7/9页 |
| 文件大小： | 0K |
| 描述： | IC REG LDO 3.3V .2A SC88A |
| 标准包装： | 1 |
| 稳压器拓扑结构： | 正，固定式 |
| 输出电压： | 3.3V |
| 输入电压： | 最高 6V |
| 电压 - 压降（标准）： | 0.16V @ 80mA |
| 稳压器数量： | 1 |
| 电流 - 输出： | 200mA |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 6-TSSOP（5 引线），SC-88A，SOT-353 |
| 供应商设备封装： | SC-88A |
| 包装： | 标准包装 |
| 其它名称： | NCP512SQ33T2GOSDKR |
NCP512
APPLICATIONS INFORMATION
PD + J(max)
VinMAX + tot
A typical application circuit for the NCP512 series is
shown in Figure 1, front page.
Input Decoupling (C1)
A 1.0 m F capacitor either ceramic or tantalum is
recommended and should be connected close to the NCP512
package. Higher values and lower ESR will improve the
overall line transient response.
TDK capacitor: C2012X5R1C105K, or C1608X5R1A105K
Output Decoupling (C2)
The NCP512 is a stable regulator and does not require any
specific Equivalent Series Resistance (ESR) or a minimum
output current. Capacitors exhibiting ESRs ranging from a
few m W up to 5.0 W can thus safely be used. The minimum
decoupling value is 1.0 m F and can be augmented to fulfill
stringent load transient requirements. The regulator accepts
ceramic chip capacitors as well as tantalum capacitors.
Larger values improve noise rejection and load regulation
transient response.
TDK capacitor: C2012X5R1C105K, C1608X5R1A105K,
or C3216X7R1C105K
Enable Operation
The enable pin will turn on the regulator when pulled high
and turn off the regulator when pulled low. These limits of
threshold are covered in the electrical specification section
of this data sheet. If the enable is not used then the pin should
be connected to V in .
Hints
Please be sure the Vin and GND lines are sufficiently
wide. When the impedance of these lines is high, there is a
Set external components, especially the output capacitor,
as close as possible to the circuit, and make leads as short as
possible.
Thermal
As power across the NCP512 increases, it might become
necessary to provide some thermal relief. The maximum
power dissipation supported by the device is dependent
upon board design and layout. Mounting pad configuration
on the PCB, the board material and also the ambient
temperature effect the rate of temperature rise for the part.
This is stating that when the NCP512 has good thermal
conductivity through the PCB, the junction temperature will
be relatively low with high power dissipation applications.
The maximum dissipation the package can handle is
given by:
T * TA
R q JA
If junction temperature is not allowed above the
maximum 125 ° C, then the NCP512 can dissipate up to
250 mW @ 25 ° C.
The power dissipated by the NCP512 can be calculated
from the following equation:
Ptot + Vin * Ignd (Iout) ) [Vin * Vout] * Iout
or
P ) Vout * Iout
Ignd ) Iout
If an 80 mA output current is needed then the ground
current from the data sheet is 40 m A. For an NCP512 (3.0 V),
the maximum input voltage will then be 6.12 V.
chance to pick up noise or cause the regulator to
malfunction.
http://onsemi.com
7
相关PDF资料 |
PDF描述 |
|---|---|
| ABM30DRSI | CONN EDGECARD 60POS DIP .156 SLD |
| AMM12DRST-S288 | CONN EDGECARD 24POS .156 EXTEND |
| RYM43DTBN-S189 | CONN EDGECARD 86POS R/A .156 SLD |
| RYM43DTBH-S189 | CONN EDGECARD 86POS R/A .156 SLD |
| RYM43DTBD-S189 | CONN EDGECARD 86POS R/A .156 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| NCP512SQ50T1 | 功能描述:低压差稳压器 - LDO 5.0V 80mA CMOS RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| NCP512SQ50T1G | 功能描述:低压差稳压器 - LDO 5.0V 80mA CMOS w/Enable RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| NCP512SQ50T2G | 功能描述:低压差稳压器 - LDO ACMOS1 LDO REGULATOR VOLTAGE REG RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| NCP51460 | 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:20mA Micropower Precision Voltage Reference |
| NCP51460SN33GEVB | 功能描述:BD EVAL 20MA PRECISE LDO BD RoHS:是 类别:编程器，开发系统 >> 评估演示板和套件 系列:* 标准包装:1 系列:PCI Express® (PCIe) 主要目的:接口，收发器，PCI Express 嵌入式:- 已用 IC / 零件:DS80PCI800 主要属性:- 次要属性:- 已供物品:板 |
发布紧急采购，3分钟左右您将得到回复。