参数资料
| 型号： | NCP5214AMNR2G |
| 厂商： | ON Semiconductor |
| 文件页数： | 16/31页 |
| 文件大小： | 0K |
| 描述： | IC CTLR NOTEBOOK DDR PWR 22-DFN |
| 产品变化通告： | Product Discontinuation 01/Oct/2008 |
| 标准包装： | 2,500 |
| 应用： | 控制器，DDR |
| 输入电压： | 4.5 V ~ 24 V |
| 输出数： | 2 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 22-VFDFN 裸露焊盘 |
| 供应商设备封装： | 22-DFN（6x5） |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页当前第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页
NCP5214A
VDDQ Regulator in Standby Mode (S3)
During state S3, a power?saving mode is activated when
the FPWM pin is pulled to VCCA. In power?saving mode,
the switching frequency is reduced with the VDDQ output
current and the low?side FET is turned off after the
detection of negative inductor current, so as to enhance the
efficiency of the VDDQ regulator at light loads. The
switching frequency can be reduced smoothly until it
reaches the minimum frequency at about 15 kHz.
Therefore, perceptible audible noise can be avoided at light
load condition.
In power?saving mode, the low?side MOSFET is turned
off after the detection of negative inductor current and the
converter cannot sink current. The power?saving mode can
be disabled by pulling the FPWM pin to ground. Then, the
converter operates in forced?PWM mode with fixed
switching frequency and ability to sink current.
Fault Protection of VDDQ Regulator
During state S0 and S3, external resistor (RL1) between
OCDDQ and VIN sets the overcurrent trip threshold for the
high?side switch. An internal 31 m A current sink (IOC) at
OCDDQ pin establishes a voltage drop across this resistor
and develops a voltage at the non?inverting input of the
current limit comparator. The voltage at the non?inverting
input is compared to the voltage at SWDDQ pin when the
high?side gate drive is high after a fixed period of blanking
time (150 ns) to avoid false current limit triggering. When
the voltage at SWDDQ is lower than that at the
non?inverting input for 4 consecutive internal clock
cycles, an overcurrent condition occurs, during which, all
outputs will be latched off to protect against a
short?to?ground condition on SWDDQ or VDDQ. The IC
will be reset once VCCA or VDDQEN is cycled.
Feedback Compensation of VDDQ Regulator
The compensation network is shown in Figures 2 and 39.
VTT Active Terminator in Normal Mode (S0)
The VTT active terminator is a two?quadrant linear
regulator with two internal N?channel power FETs. It is
capable of sinking and sourcing at least 1.5 A continuous
current and up to 2.4 A transient peak current. It is activated
in normal mode in state S0 when the VTTEN pin is HIGH
and VDDQ is in regulation. Its input power path is from
VDDQ with the internal FETs gate drive power derived
from VCCA. The VTT internal reference voltage is derived
from the DDQREF pin. The VTT output is set to VDDQ/2
when VTT output is connecting to the FBVTT pin directly.
This regulator is stable with only a minimum 20 m F output
capacitor. The VTT regulator will have an internal
soft?start when it is transited from disable to enable.
During the VTT soft?start, a current limit is used as a
current source to charge up the VTT output capacitor. The
current limit is initially 1.0 A during VTT soft?start. It is
then increased to 2.5 A after 128 internal clock cycles
which is typically 0.32 ms.
VTT Active Terminator in Standby Mode (S3)
VTT output is high?impedance in S3 mode.
Fault Protection of VTT Active Terminator
To provide protection for the internal FETs, bidirectional
current limit is implemented, preset at the minimum of
2.5 A magnitude.
Thermal Consideration of VTT Active Terminator
The VTT terminator is designed to handle large transient
output currents. If large currents are required for very long
duration, then care should be taken to ensure the maximum
junction temperature is not exceeded. The 5x6 DFN22 has
a thermal resistance of 35 _ C/W (dependent on air flow,
grade of copper, and number of vias). In order to take full
advantage from this thermal capability of this package, the
thermal pad underneath must be soldered directly onto a
PCB metal substrate to allow good thermal contact. It is
recommended that PCB with 2 oz. copper foil is used and
there should have 6 to 8 vias with 0.6 mm hole size
underneath the package’s thermal pad connecting the top
layer metal to the bottom layer metal and the internal layer
metal substrates of the PCB.
VTTREF Output
The VTTREF output tracks VDDQREF/2 at " 2%
accuracy. It has source current capability of up to 15 mA.
VTTREF should be bypassed to analog ground of the
device by 1.0 m F ceramic capacitor for stable operation.
The VTTREF is turned on as long as VDDQEN is pulled
high. In S0 mode, VTTREF soft?starts with VDDQ and
tracks VDDQREF/2. In S3 mode, VTTREF is kept on with
VDDQ. VTTREF is turned off only in S4/S5 like VDDQ
output.
Output Voltages Sensing
The VDDQ output voltage is sensed across the FBDDQ
and AGND pins. FBDDQ should be connected through a
feedback resistor divider to the VDDQ point of regulation
which is usually the local VDDQ bypass capacitor for load.
The AGND should be connected directly through a sense
trace to the remote ground sense point which is usually the
ground of local VDDQ bypass capacitor for load.
The VTT output voltage is sensed between the FBVTT
and VTTGND pins. The FBVTT should be connected to
the VTT regulation point, which is usually the VTT local
bypass capacitor, via a direct sense trace. The VTTGND
should be connected via a direct sense trace to the ground
of the VTT local bypass capacitor for load.
http://onsemi.com
16
相关PDF资料 |
PDF描述 |
|---|---|
| NCP5214MNR2G | IC CTLR NOTEBOOK DDR PWR 22-DFN |
| NCP5215MNR2G | IC CTLR SYNC BUCK DUAL 40-QFN |
| NCP5217AMNTXG | IC REG CTRLR BUCK PWM 14-QFN |
| NCP5218MNR2G | IC DDR PWR CTLR 2IN2 NTBK 22-DFN |
| NCP5220MNR2G | IC CTLR PWM DUAL BUCK PWR 20-DFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| NCP5214EVB | 功能描述:电源管理IC开发工具 ANA NCP5214 EVAL BRD RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| NCP5214MNR2 | 功能描述:DC/DC 开关控制器 2-IN-1 NOTBOOK DDR CNTLR RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| NCP5214MNR2G | 功能描述:DC/DC 开关控制器 2-IN-1 NOTBOOK DDR CNTLR RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| NCP5215 | 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:Dual Synchronous Buck Controller for Notebook Power System |
| NCP5215MNR2G | 功能描述:直流/直流开关转换器 BUCK CONTROLLER RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
发布紧急采购，3分钟左右您将得到回复。