参数资料
| 型号： | NCP5389MNR2G |
| 厂商： | ON Semiconductor |
| 文件页数： | 18/28页 |
| 文件大小： | 0K |
| 描述： | IC CTLR BUCK 2/3PHASE 32-QFN |
| 产品变化通告： | Product Discontinuation 01/Oct/2008 |
| 标准包装： | 3,000 |
| 应用： | 控制器，Intel Pentium? IV |
| 输入电压： | 10.8 V ~ 13.2 V |
| 输出数： | 3 |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 32-VFQFN 裸露焊盘 |
| 供应商设备封装： | 32-QFN（5x5） |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页当前第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
NCP5389
FUNCTIONAL DESCRIPTION
Gate Output Connections
General
The NCP5389 dual edge modulated multiphase PWM
controller is specifically designed with the necessary
features for a high current VR11 CPU power system. The
Mode
2 ? Phase
3 ? Phase
G1
Normal
Normal
G2
GND
Normal
G3
Normal
Normal
IC consists of the following blocks: Precision
Programmable DAC, Differential Remote Voltage Sense
Amplifier, High Performance Voltage Error Amplifier,
Differential Current Feedback Amplifiers, Precision
Oscillator and Triangle Wave Generators, and PWM
Comparators. Protection features include Undervoltage
Lockout, Soft ? Start, Overcurrent Protection, Overvoltage
Protection, and Power Good Monitor.
Remote Output Sensing Amplifier (RSA)
A true differential amplifier allows the NCP5389 to
measure Vcore voltage feedback with respect to the Vcore
ground reference point by connecting the Vcore reference
point to VS+, and the Vcore ground reference point to VS ? .
This configuration keeps ground potential differences
between the local controller ground and the Vcore ground
reference point from affecting regulation of Vcore between
Vcore and Vcore ground reference points. The RSA also
subtracts the DAC (minus VID offset) voltage, thereby
producing an unamplified output error voltage at the
DIFFOUT pin. This output also has a 1.3 V bias voltage to
allow both positive and negative error voltages.
Precision DAC
A precision programmable DAC is provided. This DAC
has 0.75% accuracy over the entire operating temperature
range of the part.
High Performance Voltage Error Amplifier
The error amplifier is designed to provide high slew rate
and bandwidth. Although not required when operating as
a voltage regulator, a capacitor from COMP to VFB is
required for stable unity gain test configurations.
Gate Driver Outputs and 2/3 Phase Operation
The part can be configured to run in 2 ? or 3 ? phase mode.
In 2 ? phase mode, phases 1 and 3 should be used to drive the
external gate drivers as shown in the 2 ? phase Applications
Schematic. In 2 ? phase mode, gate output G2 must be
grounded as shown in the 2 ? phase Applications Schematic.
The following truth table summarizes the modes of
operation:
These are the only allowable connection schemes to
program the modes of operation.
Differential Current Sense Amplifiers
Three differential amplifiers are provided to sense the
output current of each phase. The inputs of each current
sense amplifier must be connected across the current
sensing element of the phase controlled by the
corresponding gate output (G1, G2 or G3). If 2 phase is
unused, the differential inputs to that phase’s current
sense amplifier must be shorted together and connected
to V CCP as shown in the 2 ? phase Application
Schematics .
A voltage is generated across the current sense element
(such as an inductor or sense resistor) by the current
flowing in that phase. The output of the current sense
amplifiers are used to control three functions. First, the
output controls the adaptive voltage positioning, where the
output voltage is actively controlled according to the
output current. In this function, all of the current sense
outputs are summed so that the total output current is used
for output voltage positioning. Second, the output signal is
fed to the current limit circuit. This again is the summed
current of all phases in operation. Finally, the individual
phase current is connected to the PWM comparator. In this
way current balance is accomplished.
Oscillator and Triangle Wave Generator
A programmable precision oscillator is provided. The
oscillator ’s frequency is programmed by the resistance
connected from the ROSC pin to ground. The user will
usually form this resistance from two resistors in order to
create a voltage divider that uses the ROSC output voltage
as the reference for creating the current limit setpoint
voltage. The oscillator frequency range is 100 kHz/phase
to 1.0 MHz/phase. The oscillator generates up to 3 triangle
waveforms (symmetrical rising and falling slopes)
between 1.3 V and 2.3 V. The triangle waves have a phase
delay between them such that for 2 ? , 3 ? phase operation the
PWM outputs are separated by 180 and 120 angular
degrees, respectively.
http://onsemi.com
18
相关PDF资料 |
PDF描述 |
|---|---|
| NCP5391MNR2G | IC CTLR BUCK 2/3PHASE 32-QFN |
| NCP5392PMNR2G | IC CTLR BUCK 2/3/4PHASE 40QFN |
| NCP5392QMNR2G | IC PHASE CONTROLLER 2/3/4 40-QFN |
| NCP5392TMNR2G | IC PHASE CONTROLLER 2/3/4 40-QFN |
| NCP5393BMNR2G | IC CTLR 2/3/4PHASE CPU 48QFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| NCP5391 | 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:2/3 Phase Buck Controller for VR11 Pentium IV Processor Applications |
| NCP5391MNR2G | 功能描述:软开关 PWM 控制器 2/3 PHASE CONTROLLER RoHS:否 制造商:Fairchild Semiconductor 输出端数量: 输出电流: 开关频率: 工作电源电压:30 V 电源电流: 最大工作温度:+ 105 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Reel |
| NCP5392 | 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:2/3/4-Phase Controller for CPU Applications |
| NCP5392EMNR2G | 功能描述:DC/DC 开关控制器 2/3/4 PHASE CONTROLLER RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| NCP5392HMNR2G | 功能描述:DC/DC 开关控制器 2/3/4 PHASE CTRL RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
发布紧急采购，3分钟左右您将得到回复。