- 您现在的位置：买卖IC网 > PDF目录19235 > NCP565D2T12R4 (ON Semiconductor)IC REG LDO 1.2V 1.5A D2PAK PDF资料下载
参数资料
| 型号： | NCP565D2T12R4 |
| 厂商： | ON Semiconductor |
| 文件页数： | 7/15页 |
| 文件大小： | 0K |
| 描述： | IC REG LDO 1.2V 1.5A D2PAK |
| 产品变化通告： | Product Discontinuation 27/Jun/2007 |
| 标准包装： | 800 |
| 稳压器拓扑结构： | 正，固定式 |
| 输出电压： | 1.2V |
| 输入电压： | 2.5 V ~ 9 V |
| 电压 - 压降（标准）： | 0.9V @ 1.5A |
| 稳压器数量： | 1 |
| 电流 - 输出： | 1.5A |
| 电流 - 限制（最小）： | 1.6A |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | TO-263-3，D²Pak（2 引线+接片），TO-263AB |
| 供应商设备封装： | D2PAK |
| 包装： | 带卷 (TR) |
NCP565, NCV565
TYPICAL CHARACTERISTICS
100
90
80
70
100
90
80
70
60
50
40
30
20
10
V in = 3.0 V
V out = 0.9 V
I out = 10 mA
60
50
40
30
20
10
V in = 3.0 V
V out = 0.9 V
I out = 1.5 A
0
Start 1.0 kHz
FREQUENCY (kHz)
Stop 100 kHz
0
Start 1.0 kHz
FREQUENCY (kHz)
Stop 100 kHz
Figure 17. Noise Density vs. Frequency
Figure 18. Noise Density vs. Frequency
NOTE: Typical characteristics were measured with the same conditions as electrical characteristics.
APPLICATION INFORMATION
Vout + Vref R1 ) R2 * I Adj R2
The NCP565 low dropout linear regulator provides
adjustable voltages at currents up to 1.5 A. It features ultra
fast transient response and low dropout voltage. These
devices contain output current limiting, short circuit
protection and thermal shutdown protection.
Input, Output Capacitor and Stability
An input bypass capacitor is recommended to improve
transient response or if the regulator is located more than a
few inches from the power source. This will reduce the
circuit’s sensitivity to the input line impedance at high
frequencies and significantly enhance the output transient
response. Different types and different sizes of input
capacitors can be chosen dependent on the quality of power
supply. A 150 m F OSCON 16SA150M type from Sanyo
should be adequate for most applications. The bypass
capacitor should be mounted with shortest possible lead or
track length directly across the regulator ’s input terminals.
The output capacitor is required for stability. The NCP565
remains stable with ceramic, tantalum, and aluminum ?
electrolytic capacitors with a minimum value of 1.0 m F with
ESR between 50 m W and 2.5 W . The NCP565 is optimized
for use with a 150 m F OSCON 16SA150M type in parallel
with a 10 m F OSCON 10SL10M type from Sanyo. The
10 m F capacitor is used for best AC stability while 150 m F
capacitor is used for achieving excellent output transient
response. The output capacitors should be placed as close as
possible to the output pin of the device. If not, the excellent
load transient response of NCP565 will be degraded.
Adjustable Operation
The typical application circuit for the adjustable output
regulators is shown in Figure 2. The adjustable device
develops and maintains the nominal 0.9 V reference voltage
between Adj and ground pins. A resistor divider network R1
and R2 causes a fixed current to flow to ground. This current
creates a voltage across R1 that adds to the 0.9 V across R2
and sets the overall output voltage.
The output voltage is set according to the formula:
R2
The adjust pin current, I Adj , is typically 30 nA and
normally much lower than the current flowing through R1
and R2, thus it generates a small output voltage error that can
usually be ignored.
Load Transient Measurement
Large load current changes are always presented in
microprocessor applications. Therefore good load transient
performance is required for the power stage. NCP565 has
the feature of ultra fast transient response. Its load transient
responses in Figures 13 through 16 are tested on evaluation
board shown in Figure 19. On the evaluation board, it
consists of NCP565 regulator circuit with decoupling and
filter capacitors and the pulse controlled current sink to
obtain load current transitions. The load current transitions
are measured by current probe. Because the signal from
current probe has some time delay, it causes
un ? synchronization between the load current transition and
output voltage response, which is shown in Figures 13
through 16.
http://onsemi.com
7
相关PDF资料 |
PDF描述 |
|---|---|
| GCA06DRMH-S288 | CONN EDGECARD 12POS .125 EXTEND |
| REC3-4809SRWZ/H2/C | CONV DC/DC 3W 18-72VIN 09VOUT |
| VE-J3J-MY-F4 | CONVERTER MOD DC/DC 36V 50W |
| GCA06DRMD-S288 | CONN EDGECARD 12POS .125 EXTEND |
| ECC20DCMI-S288 | CONN EDGECARD 40POS .100 EXTEND |
相关代理商/技术参数 |
参数描述 |
|---|---|
| NCP565D2T12R4G | 功能描述:低压差稳压器 - LDO 1.2V 1.5A Fast Transient RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| NCP565D2T33G | 功能描述:低压差稳压器 - LDO ANA 1.5A LDO REG RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| NCP565D2T33R4G | 功能描述:低压差稳压器 - LDO ANA 1.5A LDO REG RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| NCP565D2TG | 功能描述:低压差稳压器 - LDO 0.9-9V 1.5A Fast Transient RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| NCP565D2TR4 | 功能描述:低压差稳压器 - LDO 0.9-9V 1.5A Fast RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
发布紧急采购，3分钟左右您将得到回复。