参数资料
| 型号： | NCP565D2TR4G |
| 厂商： | ON Semiconductor |
| 文件页数： | 8/15页 |
| 文件大小： | 0K |
| 描述： | IC REG LDO ADJ 1.5A D2PAK-5 |
| 标准包装： | 1 |
| 稳压器拓扑结构： | 正，可调式 |
| 输出电压： | 0.9 V ~ 7.7 V |
| 输入电压： | 2.5 V ~ 9 V |
| 电压 - 压降（标准）： | 0.9V @ 1.5A |
| 稳压器数量： | 1 |
| 电流 - 输出： | 1.5A |
| 电流 - 限制（最小）： | 1.6A |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | TO-263-6，D²Pak（5 引线+接片），TO-263BA |
| 供应商设备封装： | D2PAK-5 |
| 包装： | 剪切带 (CT) |
| 其它名称： | NCP565D2TR4GOSCT |
NCP565, NCV565
GEN
V out
? V CC
NCP565
V
Pulse
+
V in
Evaluation Board
GND
RL
+
GND
Scope Voltage Probe
Figure 19. Schematic for Transient Response Measurement
PCB Layout Considerations
Good PCB layout plays an important role in achieving
good load transient performance. Because it is very sensitive
to its PCB layout, particular care has to be taken when
tackling Printed Circuit Board (PCB) layout. The figures
below give an example of a layout where parasitic elements
are minimized. For microprocessor applications it is
customary to use an output capacitor network consisting of
several capacitors in parallel. This reduces the overall ESR
and reduces the instantaneous output voltage drop under
transient load conditions. The output capacitor network
should be as close as possible to the load for the best results.
The schematic of NCP565 typical application circuit, which
this PCB layout is base on, is shown in Figure 20. The output
voltage is set to 3.3 V for this demonstration board according
to the feedback resistors in the Table 1.
V in
2
V in
V out
4
V out
C 1
150 m
C 2
150 m
1
NCP565
NC Adj
GND
5
C 4
10 m
C 3
150 m
C 3
150 m
GND
3
R 2
15.8 k
R 1
42.2 k
GND
C 6
5.6 p
Figure 20. Schematic of NCP565 Typical Application Circuit
http://onsemi.com
8
相关PDF资料 |
PDF描述 |
|---|---|
| MIC5255-2.6YD5 TR | IC REG LDO 2.6V .15A TSOT23-5 |
| MIC5247-2.4YM5 TR | IC REG LDO 2.4V .15A SOT23-5 |
| RBB56DHFR-S621 | EDGECARD 112PS .050 SMD W/O PST |
| GBB35DHAR | CONN EDGECARD 70POS R/A .050 SLD |
| RBB56DHFR-S578 | EDGECARD 112POS .050 SMD W/POSTS |
相关代理商/技术参数 |
参数描述 |
|---|---|
| NCP565MN12T2G | 功能描述:低压差稳压器 - LDO ANA 1.5A LDO REG RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| NCP565MN15T2G | 功能描述:低压差稳压器 - LDO ANA 1.5A REGULATOR LO DROPOUT REG 1.5A RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| NCP565MN28T2G | 功能描述:低压差稳压器 - LDO ANA 1.5A LDO REG LO DROPOUT REG 1.5A RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| NCP565MN30T2G | 功能描述:低压差稳压器 - LDO ANA 1.5A LDO REG RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| NCP565MN33T2G | 功能描述:低压差稳压器 - LDO ANA 1.5A LDO REG RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
发布紧急采购，3分钟左右您将得到回复。