- 您现在的位置：买卖IC网 > PDF目录22190 > NCP612SQ15T2G (ON Semiconductor)IC REG LDO 1.5V .2A SC70-5 PDF资料下载
参数资料
| 型号： | NCP612SQ15T2G |
| 厂商： | ON Semiconductor |
| 文件页数： | 7/9页 |
| 文件大小： | 0K |
| 描述： | IC REG LDO 1.5V .2A SC70-5 |
| 标准包装： | 3,000 |
| 稳压器拓扑结构： | 正，固定式 |
| 输出电压： | 1.5V |
| 输入电压： | 最高 6V |
| 电压 - 压降（标准）： | 0.53V @ 100mA |
| 稳压器数量： | 1 |
| 电流 - 输出： | 200mA |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 6-TSSOP（5 引线），SC-88A，SOT-353 |
| 供应商设备封装： | SC-70 |
| 包装： | 带卷 (TR) |
NCP612, NCV612
APPLICATIONS INFORMATION
PD + J(max)
VinMAX + tot
A typical application circuit for the NCP612/NCV612 is
shown in Figure 1, front page.
Input Decoupling (C1)
A 1.0 m F capacitor either ceramic or tantalum is
recommended and should be connected close to the
NCP612/NCV612 package. Higher values and lower ESR
will improve the overall line transient response.
TDK capacitor: C2012X5R1C105K, or C1608X5R1A105K
Output Decoupling (C2)
The NCP612/NCV612 is a stable regulator and does not
require any specific Equivalent Series Resistance (ESR) or
a minimum output current. Capacitors exhibiting ESRs
ranging from a few m W up to 5.0 W can thus safely be used.
The minimum decoupling value is 1.0 m F and can be
augmented to fulfill stringent load transient requirements.
The regulator accepts ceramic chip capacitors as well as
tantalum capacitors. Larger values improve noise rejection
and load regulation transient response.
TDK capacitor: C2012X5R1C105K, C1608X5R1A105K,
or C3216X7R1C105K
Enable Operation
The enable pin will turn on the regulator when pulled high
and turn off the regulator when pulled low. These limits of
threshold are covered in the electrical specification section
of this data sheet. If the enable is not used then the pin should
be connected to V in .
Hints
Please be sure the Vin and Gnd lines are sufficiently wide.
Thermal
As power across the NCP612/NCV612 increases, it might
become necessary to provide some thermal relief. The
maximum power dissipation supported by the device is
dependent upon board design and layout. Mounting pad
configuration on the PCB, the board material and also the
ambient temperature effect the rate of temperature rise for
the part. This is stating that when the NCP612/NCV612 has
good thermal conductivity through the PCB, the junction
temperature will be relatively low with high power
dissipation applications.
The maximum dissipation the package can handle is
given by:
T * TA
R q JA
If junction temperature is not allowed above the
maximum 125 ? C, then the NCP612/NCV612 can dissipate
up to 330 mW @ 25 ? C.
The power dissipated by the NCP612/NCV612 can be
calculated from the following equation:
Ptot + Vin * Ignd (Iout) ) [Vin * Vout] * Iout
or
P ) Vout * Iout
Ignd ) Iout
If an 100 mA output current is needed then the ground
current from the data sheet is 40 m A. For an
NCP612/NCV612 (3.0 V), the maximum input voltage will
then be 6.0 V (Limited by maximum input voltage).
When the impedance of these lines is high, there is a chance
to pick up noise or cause the regulator to malfunction.
Set external components, especially the output capacitor,
as close as possible to the circuit, and make leads as short as
possible.
http://onsemi.com
7
相关PDF资料 |
PDF描述 |
|---|---|
| EBM15DRMD-S288 | CONN EDGECARD 30POS .156 EXTEND |
| VE-J1Y-IZ | CONVERTER MOD DC/DC 3.3V 16.5W |
| NCP612SQ18T2G | IC REG LDO 1.8V .2A SC70-5 |
| BH32T-C BULK | HOLDR CR2032 EASY IN/OUT UL94V-0 |
| VE-JV3-IZ | CONVERTER MOD DC/DC 24V 25W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| NCP612SQ18T1 | 功能描述:低压差稳压器 - LDO 1.8V 100mA w/Enable RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| NCP612SQ18T1G | 功能描述:低压差稳压器 - LDO 1.8V 100mA w/Enable RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| NCP612SQ18T2 | 制造商:Rochester Electronics LLC 功能描述: 制造商:ON Semiconductor 功能描述: |
| NCP612SQ18T2G | 功能描述:低压差稳压器 - LDO ACMOS1 LDO REGULATOR RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| NCP612SQ25T1 | 功能描述:低压差稳压器 - LDO 2.5V 100mA w/Enable RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
发布紧急采购，3分钟左右您将得到回复。