- 您现在的位置：买卖IC网 > PDF目录20104 > NCP691MN15T2G (ON Semiconductor)IC REG LDO 1.5V 1A 6-DFN PDF资料下载
参数资料
| 型号： | NCP691MN15T2G |
| 厂商： | ON Semiconductor |
| 文件页数： | 11/14页 |
| 文件大小： | 0K |
| 描述： | IC REG LDO 1.5V 1A 6-DFN |
| 标准包装： | 3,000 |
| 稳压器拓扑结构： | 正，固定式 |
| 输出电压： | 1.5V |
| 输入电压： | 最高 6V |
| 电压 - 压降（标准）： | 0.29V @ 1A |
| 稳压器数量： | 1 |
| 电流 - 输出： | 1A |
| 电流 - 限制（最小）： | 1.1A |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 6-VDFN 裸露焊盘 |
| 供应商设备封装： | 6-DFN（3x3） |
| 包装： | 带卷 (TR) |
NCP690, NCP691, NCP692, NCV8690
DEFINITIONS
Load Regulation
The change in output voltage for a change in output load
current at a constant temperature.
Dropout Voltage
The input/output differential at which the regulator output
no longer maintains regulation against further reductions in
input voltage. Measured, when the output drops 100 mV
below its nominal value. The junction temperature, load
current, and minimum input supply requirements affect the
dropout level.
Output Noise Voltage
This is the integrated value of the output noise over a
specified frequency range. Input voltage and output load
current are kept constant during the measurement. Results
are expressed in m V rms or nV √ Hz.
Ground Current
Ground Current is the current that flows through the
ground pin when the regulator operates without a load on its
output (I GND ). This consists of internal IC operation, bias,
etc. It is actually the difference between the input current
(measured through the LDO input pin) and the output load
current. If the regulator has an input pin that reduces its
internal bias and shuts off the output (enable/disable
Line Regulation
The change in output voltage for a change in input voltage.
The measurement is made under conditions of low
dissipation or by using pulse techniques such that the
average junction temperature is not significantly affected.
Line Transient Response
Typical output voltage overshoot and undershoot
response when the input voltage is excited with a given
slope.
Load Transient Response
Typical output voltage overshoot and undershoot
response when the output current is excited with a given
slope between no ? load and full ? load conditions.
Thermal Protection
Internal thermal shutdown circuitry is provided to protect
the integrated circuit in the event that the maximum junction
temperature is exceeded. When activated at typically 175 ° C,
the regulator turns off. This feature is provided to prevent
failures from accidental overheating.
Maximum Package Power Dissipation
The power dissipation level at which the junction
temperature reaches its maximum operating value.
function), this term is called the disable current (I DIS .)
APPLICATIONS INFORMATION
The NCP690 regulator is self ? protected with internal
thermal shutdown and internal current limit. Typical
application circuit is shown in Figure 1.
Input Decoupling (C IN )
A ceramic 10 m F capacitor is recommended and should be
connected close to the NCP690 package. Higher
capacitance and lower ESR will improve the overall line
transient response.
Output Decoupling (C OUT )
The NCP690 does not require a minimum Equivalent
Series Resistance (ESR) for the output capacitor. The
minimum output decoupling capacitor required for stability
is 1 m F. In order to improve the load transient response and
start up performance 10 m F capacitor is recommended. The
regulator is stable with ceramic chip as well as tantalum
capacitors. Larger values improve noise rejection and load
transient response.
No ? Load Regulation Considerations
The required minimum 100 m A load current is assured by
the internal resistor divider network.
The NCP690 contain an overshoot clamp circuit to
improve transient response during a load current step
release. When output voltage exceeds the nominal by
approximately 20 mV, this circuit becomes active and
clamps the output from further voltage increase. Tying the
ENABLE pin to V IN will ensure that the part is active
whenever the supply voltage is present,
Noise Decoupling
The NCP690 is a low noise regulator and needs no
external noise reduction capacitor. Unlike other low noise
regulators which require an external capacitor and have slow
startup times, the NCP690 operates without a noise
reduction capacitor, has a typical 50 m s turn ? on time and
achieves a 50 m V rms overall noise level between 10 Hz and
100 kHz.
Enable Operation
The enable pin will turn the regulator on or off. The
threshold limits are covered in the electrical characteristics
table in this data sheet. The turn ? on/turn ? off transient
voltage being supplied to the enable pin should exceed a
slew rate of 10 mV/ m s to ensure correct operation. If the
enable function is not to be used then the pin should be
connected to V IN .
Adjustable Operation
The output voltage can be adjusted from 1 to 4 times the
typical 1.250 V regulation voltage by the use of resistor
http://onsemi.com
11
相关PDF资料 |
PDF描述 |
|---|---|
| S152K39X7RN6VJ5R | CAP CER 1500PF 1KV 10% RADIAL |
| VI-212-CW-S | CONVERTER MOD DC/DC 15V 100W |
| VE-2WW-EV-F1 | CONVERTER MOD DC/DC 5.5V 150W |
| S270J33SL0R63K7R | CAP CER 27PF 3KV 5% RADIAL |
| FDH400_T50R | DIODE GEN PURPOSE 150V DO-35 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| NCP691MN18T2G | 功能描述:低压差稳压器 - LDO LDO DEVICE RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| NCP691MN25T2G | 功能描述:低压差稳压器 - LDO LDO DEVICE RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| NCP691MN33T2G | 功能描述:低压差稳压器 - LDO LDO RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| NCP691MN50T2G | 功能描述:低压差稳压器 - LDO LDO DEVICE RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| NCP691MNADJT2G | 功能描述:低压差稳压器 - LDO LDO DEVICE RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
发布紧急采购，3分钟左右您将得到回复。