参数资料
| 型号： | NCP699SN30T1G |
| 厂商： | ON Semiconductor |
| 文件页数： | 7/8页 |
| 文件大小： | 0K |
| 描述： | IC REG LDO 3V 240MA 5TSOP |
| 标准包装： | 1 |
| 稳压器拓扑结构： | 正，固定式 |
| 输出电压： | 3V |
| 输入电压： | 最高 6V |
| 电压 - 压降（标准）： | 0.34V @ 150mA |
| 稳压器数量： | 1 |
| 电流 - 输出： | 240mA |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 6-TSOP（0.059"，1.50mm 宽）5 引线 |
| 供应商设备封装： | 5-TSOP |
| 包装： | 标准包装 |
| 产品目录页面： | 1120 (CN2011-ZH PDF) |
| 其它名称： | NCP699SN30T1GOSDKR |
NCP699
APPLICATIONS INFORMATION
PD + J(max)
A typical application circuit for the NCP699 series is
shown in Figure 1, front page.
Input Decoupling (C in )
A 1.0 m F capacitor either ceramic or tantalum is
recommended and should be connected close to the NCP699
package. Higher values and lower ESR will improve the
overall line transient response.
TDK capacitor: C2012X5R1C105K, or C1608X5R1A105K
Output Decoupling (C out )
The NCP699 is a stable regulator and does not require any
specific Equivalent Series Resistance (ESR) or a minimum
output current. Capacitors exhibiting ESRs ranging from a
few m W up to 5.0 W can thus safely be used. The minimum
decoupling value is 1.0 m F and can be augmented to fulfill
stringent load transient requirements. The regulator accepts
ceramic chip capacitors as well as tantalum capacitors.
Larger values improve noise rejection and load regulation
transient response.
TDK capacitor: C2012X5R1C105K, C1608X5R1A105K,
or C3216X7R1C105K
Enable Operation
The enable pin will turn on the regulator when pulled high
and turn off the regulator when pulled low. These limits of
threshold are covered in the electrical specification section
Set external components, especially the output capacitor,
as close as possible to the circuit, and make leads as short as
possible.
Thermal
As power across the NCP699 increases, it might become
necessary to provide some thermal relief. The maximum
power dissipation supported by the device is dependent
upon board design and layout. Mounting pad configuration
on the PCB, the board material and also the ambient
temperature effect the rate of temperature rise for the part.
This is stating that when the NCP699 has good thermal
conductivity through the PCB, the junction temperature will
be relatively low with high power dissipation applications.
The maximum dissipation the package can handle is
given by:
T * TA
R q JA
If junction temperature is not allowed above the
maximum 125 ° C, then the NCP699 can dissipate up to
400 mW @ 25 ° C.
The power dissipated by the NCP699 can be calculated
from the following equation:
Ptot + Vin * Ignd (@Iout) ) [Vin * Vout] * Iout
or
of this data sheet. If the enable is not used then the pin should
be connected to V in .
VinMAX +
Ptot ) Vout * Iout
Ignd(@Iout) ) Iout
Hints
Please be sure the Vin and Gnd lines are sufficiently wide.
When the impedance of these lines is high, there is a chance
to pick up noise or cause the regulator to malfunction.
ORDERING INFORMATION
If an 150 mA output current is needed then the ground
current from the data sheet is 40 m A. For an NCP699 (3.0 V),
the maximum input voltage will then be 5.65 V.
Device
NCP699SN13T1G
NCP699SN14T1G
NCP699SN15T1G
NCP699SN18T1G
NCP699SN25T1G
NCP699SN28T1G
NCP699SN29T1G
NCP699SN30T1G
NCP699SN31T1G
NCP699SN33T1G
NCP699SN34T1G
NCP699SN45T1G
NCP699SN50T1G
Nominal
Output Voltage*
1.3
1.4
1.5
1.8
2.5
2.8
2.9
3.0
3.1
3.3
3.4
4.5
5.0
Marking
LJY
AA4
LJP
LJS
LJT
LJU
ACP
LJV
AAE
LJW
ACF
ACQ
LJX
Package
TSOP ? 5
(Pb ? Free)
Shipping ?
3000 Units/
7 ″ Tape & Reel
*Additional voltages in 100 mV steps are available upon request by contacting your ON Semiconductor representative.
?For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specification Brochure, BRD8011/D.
http://onsemi.com
7
相关PDF资料 |
PDF描述 |
|---|---|
| TPS78101DRVT | IC REG LDO ADJ .15A 6SON |
| ACM36DSEP-S243 | CONN EDGECARD 72POS .156 EYELET |
| NCP699SN18T1G | IC REG LDO 1.8V 240MA 5TSOP |
| ABM36DSEP-S243 | CONN EDGECARD 72POS .156 EYELET |
| NCP698SQ25T1G | IC REG LDO 2.5V .28A SC-82AB |
相关代理商/技术参数 |
参数描述 |
|---|---|
| NCP699SN31T1G | 功能描述:低压差稳压器 - LDO 150mA 3.1V CMOS LDO RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| NCP699SN33T1G | 功能描述:低压差稳压器 - LDO CMOS LDO 150mA 3.3V RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| NCP699SN34T1G | 功能描述:低压差稳压器 - LDO 150mA 3.4V CMOS LDO RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| NCP699SN45T1G | 功能描述:低压差稳压器 - LDO 150mA 4.5V CMOS LDO RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| NCP699SN50T1G | 功能描述:低压差稳压器 - LDO CMOS LDO 150mA 5.0V RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
发布紧急采购，3分钟左右您将得到回复。