参数资料
| 型号： | NCS2552SNT1G |
| 厂商： | ON Semiconductor |
| 文件页数： | 4/13页 |
| 文件大小： | 0K |
| 描述： | IC OPAMP CFA MONO 750MHZ 6-TSOP |
| 产品变化通告： | Product Discontinuation 21/Jun/2007 |
| 标准包装： | 3,000 |
| 放大器类型： | 电压反馈 |
| 电路数： | 1 |
| 转换速率： | 1700 V/µs |
| -3db带宽： | 750MHz |
| 电流 - 输入偏压： | 3.2µA |
| 电压 - 输入偏移： | 10000µV |
| 电流 - 电源： | 13mA |
| 电流 - 输出 / 通道： | 100mA |
| 电压 - 电源，单路/双路(±)： | 5 V ~ 10 V，±2.5 V ~ 5 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | SC-74，SOT-457 |
| 供应商设备封装： | 6-TSOP |
| 包装： | 带卷 (TR) |
NCS2552
http://onsemi.com
12
Printed Circuit Board Layout Techniques
Proper high speed PCB design rules should be used for all
wideband amplifiers as the PCB parasitics can affect the
overall performance. Most important are stray capacitances
at the output and inverting input nodes as it can effect
peaking and bandwidth. A space (3/16″ is plenty) should be
left around the signal lines to minimize coupling. Also,
signal lines connecting the feedback and gain resistors
should be short enough so that their associated inductance
does not cause high frequency gain errors. Line lengths less
than 1/4″ are recommended.
Video Performance
This device designed to provide good performance with
NTSC, PAL, and HDTV video signals. Best performance is
obtained with back terminated loads as performance is
degraded as the load is increased. The back termination
reduces reflections from the transmission line and
effectively masks transmission line and other parasitic
capacitances from the amplifier output stage.
ESD Protection
All device pins have limited ESD protection using internal
diodes to power supplies as specified in the attributes table
(see Figure 25). These diodes provide moderate protection
to input overdrive voltages above the supplies. The ESD
diodes can support high input currents with current limiting
series resistors. Keep these resistor values as low as possible
since high values degrade both noise performance and
frequency response. Under closedloop operation, the ESD
diodes have no effect on circuit performance. However,
under certain conditions the ESD diodes will be evident. If
the device is driven into a slewing condition, the ESD diodes
will clamp large differential voltages until the feedback loop
restores closedloop operation. Also, if the device is
powered down and a large input signal is applied, the ESD
diodes will conduct.
NOTE: Human Body Model for +IN and –IN pins are
rated at 0.8kV while all other pins are rated at
2.0kV.
VCC
Internal
Circuitry
VEE
External
Pin
Figure 25. Internal ESD Protection
ORDERING INFORMATION
Device
Package
Shipping
NCS2552SNT1G
SOT236 (TSOP6)
(PbFree)
3000 Tape & Reel
For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
相关PDF资料 |
PDF描述 |
|---|---|
| NCS7101SN1T1G | IC OPAMP SGL R-R 1.8V 5TSOP |
| NCV2001SQ2T2G | IC OP AMP R-R SGL 1V SC88-5 |
| NCV2002SN2T1 | IC OPAMP R-R 0.9V 1A 6-TSOP |
| NCV2904DMR2G | IC OPAMP DUAL SGL SUPP LP 8MICRO |
| NCV33072DR2G | IC OP AMP MONOLITHIC 8SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| NCS2553 | 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:3-Channel Video Amp with Standard Definition Reconstruction Filters |
| NCS2553DG | 功能描述:视频放大器 TRPL V-AMP 8M FILTER RoHS:否 制造商:ON Semiconductor 通道数量:4 电源类型: 工作电源电压:3.3 V, 5 V 电源电流: 最小工作温度: 最大工作温度: 封装 / 箱体:TSSOP-14 封装:Reel |
| NCS2553DGEVB | 功能描述:电源管理IC开发工具 NCS2553D EVAL BOARD RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| NCS2553DR2G | 功能描述:视频放大器 TRPL V-AMP 8M FILTER RoHS:否 制造商:ON Semiconductor 通道数量:4 电源类型: 工作电源电压:3.3 V, 5 V 电源电流: 最小工作温度: 最大工作温度: 封装 / 箱体:TSSOP-14 封装:Reel |
| NCS2554 | 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:Four-Channel Video Driver with SD Reconstruction Filters |
发布紧急采购，3分钟左右您将得到回复。