- 您现在的位置：买卖IC网 > PDF目录224596 > NCS6S4803L5C (MURATA POWER SOLUTIONS INC) 1-OUTPUT 5 W DC-DC REG PWR SUPPLY MODULE PDF资料下载
参数资料
| 型号： | NCS6S4803L5C |
| 厂商： | MURATA POWER SOLUTIONS INC |
| 元件分类： | 电源模块 |
| 英文描述： | 1-OUTPUT 5 W DC-DC REG PWR SUPPLY MODULE |
| 封装： | ROHS COMPLIANT, METAL PACKAGE-23/8 |
| 文件页数： | 4/10页 |
| 文件大小： | 214K |
| 代理商： | NCS6S4803L5C |
Technical enquiries email: mk@murata-ps.com, tel: +44 (0)1908 615232
NCS6 Series
Isolated 6W 4:1 Input Single & Dual Output DC/DC Converters
2010-07-21
KDC_NCS6C.C03 Page 3 of 10
www.murata-ps.com
TECHNICAL NOTES
ISOLATION VOLTAGE
‘Hi Pot Test’, ‘Flash Tested’, ‘Withstand Voltage’, ‘Proof Voltage’, ‘Dielectric Withstand Voltage’ & ‘Isolation Test Voltage’ are all terms that relate to the same thing, a test voltage,
applied for a specied time, across a component designed to provide electrical isolation, to verify the integrity of that isolation.
Murata Power Solutions NCS6 series of DC/DC converters are all 100% production tested at their stated isolation voltage. This is 1.5kVDC for 1 second.
A question commonly asked is, “What is the continuous voltage that can be applied across the part in normal operation?”
For a part holding no specic agency approvals, such as the NCS6 series, both input and output should normally be maintained within SELV limits i.e. less than 42.4V peak, or
60VDC. The isolation test voltage represents a measure of immunity to transient voltages and the part should never be used as an element of a safety isolation system. The part
could be expected to function correctly with several hundred volts offset applied continuously across the isolation barrier; but then the circuitry on both sides of the barrier must
be regarded as operating at an unsafe voltage and further isolation/insulation systems must form a barrier between these circuits and any user-accessible circuitry according to
safety standard requirements.
REPEATED HIGH-VOLTAGE ISOLATION TESTING
It is well known that repeated high-voltage isolation testing of a barrier component can actually degrade isolation capability, to a lesser or greater degree depending on materials,
construction and environment. The NCS6 series has an ER ferrite core, with no additional insulation between primary and secondary windings of enameled wire. While parts can be
expected to withstand several times the stated test voltage, the isolation capability does depend on the wire insulation. Any material, including this enamel (typically polyurethane)
is susceptible to eventual chemical degradation when subject to very high applied voltages thus implying that the number of tests should be strictly limited. We therefore strongly
advise against repeated high voltage isolation testing, but if it is absolutely required, that the voltage be reduced by 20% from specied test voltage.
This consideration equally applies to agency recognized parts rated for better than functional isolation where the wire enamel insulation is always supplemented by a further
insulation system of physical spacing or barriers.
RoHS COMPLIANCE INFORMATION
This series is compatible with RoHS soldering systems with a peak wave solder temperature of 260C for 10 seconds. The pin termination nish
on this product series is a Gold ash (0.05-0.10 micron) over Nickel Preplate. The series is backward compatible with Sn/Pb soldering systems.
For further information, please visit www.murata-ps.com/rohs
CHARACTERISATION TEST METHODS
Ripple & Noise Characterisation Method
Ripple and noise measurements are performed with the following test conguration.
C1
1μF X7R multilayer ceramic capacitor, voltage rating to be a minimum of 3 times the output voltage of the DC/DC converter
C2
10μF tantalum capacitor, voltage rating to be a minimum of 1.5 times the output voltage of the DC/DC converter with an ESR of less
than 100mΩ at 100 kHz
C3
100nF multilayer ceramic capacitor, general purpose
R1
450Ω resistor, carbon lm, ±1% tolerance
R2
50Ω BNC termination
T1
3T of the coax cable through a ferrite toroid
RLOAD
Resistive load to the maximum power rating of the DC/DC converter. Connections should be made via twisted wires
Measured values are multiplied by 10 to obtain the specied values.
Differential Mode Noise Test Schematic
OSCILLOSCOPE
Y INPUT
SUPPLY
C1 C2 C3
R1
T1
R2
Input
Output
DC/DC Converter
R LOAD
+
-
相关PDF资料 |
PDF描述 |
|---|---|
| NCT050C-20.0000 | CRYSTAL OSCILLATOR, CLOCK, 20 MHz, TTL OUTPUT |
| NCT250A-FREQ-OUT3 | CRYSTAL OSCILLATOR, CLOCK, 4 MHz - 20 MHz, TTL OUTPUT |
| NCT240B-FREQ-OUT3 | CRYSTAL OSCILLATOR, CLOCK, 0.5 MHz - 4 MHz, TTL OUTPUT |
| NCT270B-FREQ-OUT3 | CRYSTAL OSCILLATOR, CLOCK, 20 MHz - 66.6667 MHz, TTL OUTPUT |
| NCT040C-FREQ-OUT3 | CRYSTAL OSCILLATOR, CLOCK, 0.5 MHz - 4 MHz, TTL OUTPUT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| NCS6S4805C | 功能描述:DC/DC转换器 6W 48Vin 6Vout 1.2A Isolated TH RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸: |
| NCS6S4812C | 功能描述:DC/DC转换器 6W 48Vin 12Vout 0.5A Isolated TH RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸: |
| NCS6S4815C | 功能描述:DC/DC转换器 6W 48Vin 15Vout 0.4A Isolated TH RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸: |
| NCS7101 | 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:1.8 Volt Rail−to−Rail Operational Amplifier |
| NCS7101/D | 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:1.8 Volt Rail-to-Rail Operational Amplifier |
发布紧急采购，3分钟左右您将得到回复。