- 您现在的位置：买卖IC网 > PDF目录16876 > NCS8353MNGEVB (ON Semiconductor)BOARD EVAL NCS8353 AUDIO AMP PDF资料下载
参数资料
| 型号： | NCS8353MNGEVB |
| 厂商： | ON Semiconductor |
| 文件页数： | 5/14页 |
| 文件大小： | 0K |
| 描述： | BOARD EVAL NCS8353 AUDIO AMP |
| 设计资源： | NCS8353MNGEVB Schematic NCS8353MNGEVB Gerber Files NCS8353MNGEVB Bill of Materials |
| 标准包装： | 1 |
| 放大器类型： | D 类 |
| 输出类型： | 2 通道（立体声） |
| 在某负载时最大输出功率 x 通道数量： | 20W x 2 @ 8 欧姆 |
| 电源电压： | 8 V ~ 26 V |
| 工作温度： | -40°C ~ 85°C |
| 板类型： | 完全填充 |
| 已用 IC / 零件： | NCS8353 |
| 已供物品： | 板 |
| 其它名称： | NCS8353MNGEVBOS |
NCS8353
http://onsemi.com
13
Pop and Click Suppression
Pop and click is often a function of charge difference from
input coupling and bypass capacitors, momentary
differential offset voltages across the speaker, or state
changes of the input source (codec) that cause an abrupt
change in current to flow through the loudspeaker. In all
cases these pop and click phenomena occur during the
following power sequences:
Power supply power-up or power down (codec or amp).
Entering or releasing from shutdown/mute (codec or
amp).
State changes in the audio codec; e.g., switching
between audio sources.
Due to the voltage changes in the audio signal chain a
momentary current will flow through the loudspeaker.
When current flows through the voice coil of a loudspeaker
it causes the diaphragm to move thus causing a popping and
clicking sound.
The NCS8353 includes pop and click suppression
circuitry that creates a slow ramp to bias the amplifier during
the previously mentioned power sequences. In order to
eliminate “pop and click” noises during transition, the
output power in the load must not be established or cutoff
suddenly. When logic high is applied to the shutdown pin,
the internal biasing voltage rises quickly and once the output
DC level is around the common mode voltage, the gain is
established slowly. This method to turn on the device is
optimized in terms of rejection of “pop and click” noises.
The device has the same behavior when it is turned-off by a
logic low on the enable pin. No power is delivered to the load
60 ms after a falling edge on the enable pin. Due to the fast
turn on and off times, the shutdown signal can be used as a
mute signal as well.
相关PDF资料 |
PDF描述 |
|---|---|
| 0982660116 | CBL 10POS 0.5MM JMPR TYPE D 1' |
| PCM16XK1 | PROCESSOR MODULE FOR PIC16F87X |
| RBB06DHRT | CONN CARD EXTEND 12POS .050" |
| 207W213-3-01/42-0 | BOOT MOLDED |
| EEV-FC1V101P | CAP ALUM 100UF 35V 20% SMD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| NCS8353MNTXG | 功能描述:音频放大器 20W CLASS D AUDIO AMP RoHS:否 制造商:STMicroelectronics 产品:General Purpose Audio Amplifiers 输出类型:Digital 输出功率: THD + 噪声: 工作电源电压:3.3 V 电源电流: 最大功率耗散: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:TQFP-64 封装:Reel |
| NCS-8-4-12 | 制造商:z*INACTIVE* NATIONAL 功能描述: |
| NCSA3102 | 制造商:Hubbell Wiring Device-Kellems 功能描述:N-QCK, SNAP, FEM ANG PLG, 3P, #24, 2M |
| NCSA3105 | 制造商:Hubbell Wiring Device-Kellems 功能描述:N-QCK, SNAP, FEM ANG PLG, 3P, #24, 5M |
| NCSA3202 | 制造商:Hubbell Wiring Device-Kellems 功能描述:NANO-QCK, SNAP ANG FEM PLG, 3P, 2M |
发布紧急采购，3分钟左右您将得到回复。