参数资料
| 型号： | NCV2575D2T-ADJG |
| 厂商： | ON Semiconductor |
| 文件页数： | 11/28页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK ADJ 1A D2PAK-5 |
| 产品变化通告： | Product Discontinuation 27/Jan/2012 |
| 标准包装： | 50 |
| 类型： | 降压（降压） |
| 输出类型： | 可调式 |
| 输出数： | 1 |
| 输出电压： | 1.23 V ~ 37 V |
| 输入电压： | 4.75 V ~ 40 V |
| PWM 型： | 电流/电压模式 |
| 频率 - 开关： | 52kHz |
| 电流 - 输出： | 1A |
| 同步整流器： | 无 |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | TO-263-6，D²Pak（5 引线+接片），TO-263BA |
| 包装： | 管件 |
| 供应商设备封装： | D2PAK |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页当前第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
LM2575, NCV2575
Procedure (Fixed Output Voltage Version) (continued) In order to simplify the switching regulator design, a step ? by ? step design
procedure and example is provided.
V out + V
1 )
V out + 1.23 1 )
R1 Select R1 = 1.8 k W
V out 8.0 V
R2 + R1 * 1 + 1.8 k * 1
ref
Procedure
5. Output Capacitor Selection (C out )
A. Since the LM2575 is a forward ? mode switching regulator
with voltage mode control, its open loop 2 ? pole ? 2 ? zero
frequency characteristic has the dominant pole ? pair
determined by the output capacitor and inductor values. For
stable operation and an acceptable ripple voltage,
(approximately 1% of the output voltage) a value between
100 m F and 470 m F is recommended.
B. Due to the fact that the higher voltage electrolytic capacitors
generally have lower ESR (Equivalent Series Resistance)
numbers, the output capacitor’s voltage rating should be at
least 1.5 times greater than the output voltage. For a 5.0 V
regulator, a rating at least 8V is appropriate, and a 10 V or
16 V rating is recommended.
Procedure (Adjustable Output Version: LM2575 ? Adj)
Procedure
Given Parameters:
V out = Regulated Output Voltage
V in(max) = Maximum DC Input Voltage
I Load(max) = Maximum Load Current
1. Programming Output Voltage
To select the right programming resistor R1 and R2 value (see
Figure 14) use the following formula:
R2
ref R1 where V ref = 1.23 V
Resistor R1 can be between 1.0 k and 5.0 k W . (For best
temperature coefficient and stability with time, use 1% metal
Example
5. Output Capacitor Selection (C out )
A. C out = 100 m F to 470 m F standard aluminium electrolytic.
B. Capacitor voltage rating = 16 V.
Example
Given Parameters:
V out = 8.0 V
V in(max) = 12 V
I Load(max) = 1.0 A
1. Programming Output Voltage (selecting R1 and R2)
Select R1 and R2:
R2
V 1.23 V
ref
film resistors).
R2 + R1
V out
V
1
R2 = 9.91 k W , choose a 9.88 k metal film resistor.
2. Input Capacitor Selection (C in )
To prevent large voltage transients from appearing at the input
and for stable operation of the converter, an aluminium or
tantalum electrolytic bypass capacitor is needed between the
input pin +V in and ground pin GND This capacitor should be
located close to the IC using short leads. This capacitor should
have a low ESR (Equivalent Series Resistance) value .
For additional information see input capacitor section in the
“External Components” section of this data sheet.
3. Catch Diode Selection (D1)
A. Since the diode maximum peak current exceeds the
regulator maximum load current the catch diode current
rating must be at least 1.2 times greater than the maximum
load current. For a robust design, the diode should have a
current rating equal to the maximum current limit of the
LM2575 to be able to withstand a continuous output short.
B. The reverse voltage rating of the diode should be at least
1.25 times the maximum input voltage.
2. Input Capacitor Selection (C in )
A 100 m F aluminium electrolytic capacitor located near the
input and ground pin provides sufficient bypassing.
3. Catch Diode Selection (D1)
A. For this example, a 3.0 A current rating is adequate.
B. Use a 20 V 1N5820 or MBR320 Schottky diode or any
suggested fast recovery diode in the Table 4.
http://onsemi.com
11
相关PDF资料 |
PDF描述 |
|---|---|
| NCV3011DTBR2G | IC REG CTRLR BUCK PWM VM 14TSSOP |
| NCV3012DTBR2G | IC REG CTRLR BUCK PWM VM 14TSSOP |
| NCV301LSN40T1G | IC VOLT DETECTOR 4.0V 5TSOP |
| NCV301LSN45T1G | IC VOLT DETECTOR 4.5V TSOP-5 |
| NCV303LSN17T1G | IC VOLT DETECTOR 1.7V TSOP-5 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| NCV2575D2TADJR4G | 功能描述:直流/直流开关调节器 ANA ADJ 1A PW SW REG RoHS:否 制造商:International Rectifier 最大输入电压:21 V 开关频率:1.5 MHz 输出电压:0.5 V to 0.86 V 输出电流:4 A 输出端数量: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PQFN 4 x 5 |
| NCV2575D2T-ADJR4G | 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:1.0 A, Adjustable Output Voltage, Step-Down Switching Regulator |
| NCV2890 | 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:1.0 Watt Audio Power Amplifier |
| NCV2890DMR2G | 功能描述:音频放大器 ANA 1W MONO PWR AMP RoHS:否 制造商:STMicroelectronics 产品:General Purpose Audio Amplifiers 输出类型:Digital 输出功率: THD + 噪声: 工作电源电压:3.3 V 电源电流: 最大功率耗散: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:TQFP-64 封装:Reel |
| NCV2901 | 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:Single Supply Quad Comparators |
发布紧急采购，3分钟左右您将得到回复。