- 您现在的位置：买卖IC网 > PDF目录15203 > NCV303LSN46T1G (ON Semiconductor)IC VOLT DETECTOR 4.6V TSOP-5 PDF资料下载
参数资料
| 型号： | NCV303LSN46T1G |
| 厂商： | ON Semiconductor |
| 文件页数： | 21/26页 |
| 文件大小： | 0K |
| 描述： | IC VOLT DETECTOR 4.6V TSOP-5 |
| 标准包装： | 3,000 |
| 类型： | 简单复位/加电复位 |
| 监视电压数目： | 1 |
| 输出： | 开路漏极或开路集电极 |
| 复位： | 低有效 |
| 复位超时： | 可调节/可选择 |
| 电压 - 阀值： | 4.6V |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 6-TSOP（0.059"，1.50mm 宽）5 引线 |
| 供应商设备封装： | 5-TSOP |
| 包装： | 带卷 (TR) |
NCP302, NCP303
5
C D
Power Supply 1
(System Core)
R1 is Optional C D Pin Pullup
2 Input
R1
NCP302L
Series
C D
3 GND
1
Reset Output
V P
* R P
*Required for
NCP303
To MCU or
Logic Circuitry
3.3 V Power Supply 2
(I/O Subsystem)
2
Input
NCP301
LSN30T1
1
Reset Output
5.0 V Power Supply 3
3
GND
(Peripheral Subsystem)
2
Input
NCP301
LSN45T1
1
Reset Output
Power Supply 1
Power Supply 2
Power Supply 3
V IN
0V
0V
0V
3
GND
C D Pin
V IN
V TCD
0V
NCP302L
RESET Output
0V
Note: V TCD 0.675 * V IN
t D2
t D2
t D2
t D2
Figure 46. Multi ? Rail Supply Undervoltage Monitor with Power Good
This circuit monitors multiple power supply rails for
undervoltage conditions. If any of the three power supplies
are in an undervoltage condition, the NCP302 reset output
will be immediately set to an active low level. All three
power supplies must be above their minimum voltage levels
for the NCP302 reset output to generate a “Power Good”
level (Reset Output = Power Supply 1 or V P ).
Optionally, R1 may be added to provide a smaller
effective C D pin pullup resistance, (R D ’), where
R D ’ = R1 || R D , with R D (internal C D pin pullup resistance)
approximately equal to 1.0 M W , and R1 > 5 k W . If R1 << R D ,
then R1 also can decrease the reset output delay time (t D2 )
variance over the operating temperature range.
The Power Good signal time delay (t D2 ) can be estimated
by: t D2 ≈ R D * C D , with R D in Ohms, and C D in Farads. If
R1 is installed, then R D ’ is substituted for R D . R P is added
only if using the NCP303 to replace the NCP302. This
allows the Reset Output to be pulled up to V P , which can be
the Power Supply 1 or an independent power supply rail.
http://onsemi.com
21
相关PDF资料 |
PDF描述 |
|---|---|
| NCV303LSN43T1G | IC VOLT DETECTOR 4.3V TSOP-5 |
| ISL6843CBZ | IC PWM CONTROLLER |
| ISL6341CCRZ-T | IC REG CTRLR BUCK PWM VM 10-TDFN |
| H2ABT-10108-V8-ND | JUMPER-H1502TR/A3048V/H1500TR 8" |
| ISL6341CRZ-T | IC REG CTRLR BUCK PWM VM 10-TDFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| NCV303LSN47T1 | 功能描述:电压监测器/监控器 4.7V Detector RoHS:否 制造商:Texas Instruments 监测电压数:2 监测电压:Adjustable 输出类型:Open Drain 欠电压阈值: 过电压阈值: 准确性:1 % 工作电源电压:1.5 V to 6.5 V 工作电源电流:1.8 uA 最大工作温度:+ 125 C 封装 / 箱体:SON-6 安装风格:SMD/SMT |
| NCV303LSN47T1G | 功能描述:电压监测器/监控器 4.7V Detector w/N-Channel Output RoHS:否 制造商:Texas Instruments 监测电压数:2 监测电压:Adjustable 输出类型:Open Drain 欠电压阈值: 过电压阈值: 准确性:1 % 工作电源电压:1.5 V to 6.5 V 工作电源电流:1.8 uA 最大工作温度:+ 125 C 封装 / 箱体:SON-6 安装风格:SMD/SMT |
| NCV303LSN49T1 | 功能描述:电压监测器/监控器 4.9V Detector RoHS:否 制造商:Texas Instruments 监测电压数:2 监测电压:Adjustable 输出类型:Open Drain 欠电压阈值: 过电压阈值: 准确性:1 % 工作电源电压:1.5 V to 6.5 V 工作电源电流:1.8 uA 最大工作温度:+ 125 C 封装 / 箱体:SON-6 安装风格:SMD/SMT |
| NCV303LSN49T1G | 功能描述:电压监测器/监控器 4.9V Detector w/N-Channel Output RoHS:否 制造商:Texas Instruments 监测电压数:2 监测电压:Adjustable 输出类型:Open Drain 欠电压阈值: 过电压阈值: 准确性:1 % 工作电源电压:1.5 V to 6.5 V 工作电源电流:1.8 uA 最大工作温度:+ 125 C 封装 / 箱体:SON-6 安装风格:SMD/SMT |
| NCV305LSQ44T1G | 制造商:ON Semiconductor 功能描述:ANA UNDRVLTG DTECT 4.4V A - Tape and Reel 制造商:ON Semiconductor 功能描述:REEL / ANA UNDRVLTG DTECT 4.4V A |
发布紧急采购，3分钟左右您将得到回复。