参数资料
| 型号： | NCV317MBSTT3G |
| 厂商： | ON Semiconductor |
| 文件页数： | 8/14页 |
| 文件大小： | 0K |
| 描述： | IC REG LDO ADJ .5A SOT-223-4 |
| 标准包装： | 4,000 |
| 稳压器拓扑结构： | 正，可调式 |
| 输出电压： | 1.2 V ~ 37 V |
| 输入电压： | 最高 40 V |
| 稳压器数量： | 1 |
| 电流 - 输出： | 500mA（最小） |
| 电流 - 限制（最小）： | 500mA |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | TO-261-4，TO-261AA |
| 供应商设备封装： | SOT-223 |
| 包装： | 带卷 (TR) |
LM317M, NCV317MA, NCV317M
APPLICATIONS INFORMATION
Vout + Vref 1 ) 2 ) IAdj R2
Basic Circuit Operation
The LM317M is a three ? terminal floating regulator. In
operation, the LM317M develops and maintains a nominal
1.25 V reference (V ref ) between its output and adjustment
terminals. This reference voltage is converted to a
programming current (I PROG ) by R 1 (see Figure 19), and this
constant current flows through R 2 to ground. The regulated
output voltage is given by:
R
R1
Since the current from the terminal (I Adj ) represents an
error term in the equation, the LM317M was designed to
control I Adj to less than 100 m A and keep it constant. To do
this, all quiescent operating current is returned to the output
terminal. This imposes the requirement for a minimum load
current. If the load current is less than this minimum, the
output voltage will rise.
Since the LM317M is a floating regulator, it is only the
voltage differential across the circuit which is important to
performance, and operation at high voltages with respect to
ground is possible.
External Capacitors
A 0.1 m F disc or 1.0 m F tantalum input bypass capacitor
(C in ) is recommended to reduce the sensitivity to input line
impedance.
The adjustment terminal may be bypassed to ground to
improve ripple rejection. This capacitor (C Adj ) prevents
ripple from being amplified as the output voltage is
increased. A 10 m F capacitor should improve ripple
rejection about 15 dB at 120 Hz in a 10 V application.
Although the LM317M is stable with no output
capacitance, like any feedback circuit, certain values of
external capacitance can cause excessive ringing. An output
capacitance (C O ) in the form of a 1.0 m F tantalum or 25 m F
aluminum electrolytic capacitor on the output swamps this
effect and insures stability.
Protection Diodes
When external capacitors are used with any IC regulator
it is sometimes necessary to add protection diodes to prevent
the capacitors from discharging through low current points
into the regulator.
Figure 20 shows the LM317M with the recommended
protection diodes for output voltages in excess of 25 V or
V in
LM317M
Adjust
V out
V ref
+
R 1
I PROG
high capacitance values (C O > 25 m F, C Adj > 5.0 m F). Diode
D 1 prevents C O from discharging thru the IC during an input
short circuit. Diode D 2 protects against capacitor C Adj
discharging through the IC during an output short circuit.
The combination of diodes D 1 and D 2 prevents C Adj from
discharging through the IC during an input short circuit.
V out
I Adj
V ref = 1.25 V Typical
R 2
V in
D 1
1N4002
LM317M
V out
V out
Figure 19. Basic Circuit Configuration
C in
R 1
D 2
+
C O
Load Regulation
The LM317M is capable of providing extremely good
load regulation, but a few precautions are needed to obtain
maximum performance. For best performance, the
Adjust
R 2
C Adj
1N4002
programming resistor (R 1 ) should be connected as close to
the regulator as possible to minimize line drops which
effectively appear in series with the reference, thereby
degrading regulation. The ground end of R 2 can be returned
near the load ground to provide remote ground sensing and
improve load regulation.
http://onsemi.com
8
Figure 20. Voltage Regulator with
Protection Diodes
相关PDF资料 |
PDF描述 |
|---|---|
| NCV33064P-5RPG | IC SENSOR UNDERVOLTAGE TO92 |
| NCV33161DR2G | IC VOLTAGE MONITOR UNIV 8-SOIC |
| NCV33163DWR2 | IC REG BUCK BOOST INV ADJ 16SOIC |
| NCV33164D-5R2G | IC SENSOR UNDERVOLTAGE 5V 8SOIC |
| NCV4264-2ST50T3G | IC REG LDO 5V .1A SOT-223 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| NCV33033 | 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:Brushless DC Motor Controller |
| NCV33033DWR2 | 功能描述:马达/运动/点火控制器和驱动器 DC Brushless Motor RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| NCV33033DWR2G | 功能描述:马达/运动/点火控制器和驱动器 DC Brushless Motor Controller RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| NCV33035 | 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:Brushless DC Motor Controller |
| NCV33035DWR2 | 功能描述:马达/运动/点火控制器和驱动器 DC Brushless Motor RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。