参数资料
| 型号： | NCV7601PG |
| 厂商： | ON Semiconductor |
| 文件页数： | 5/6页 |
| 文件大小： | 0K |
| 描述： | IC DRIVER QUAD AUTO GRADE 16DIP |
| 产品变化通告： | Product Discontinuation 09/Jan/2008 |
| 标准包装： | 25 |
| 类型： | 继电器/灯驱动器 |
| 输入类型： | 非反相 |
| 输出数： | 4 |
| 电流 - 峰值输出： | 1.8A |
| 电源电压： | 4 V ~ 5.5 V |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 通孔 |
| 封装/外壳： | 16-DIP（0.300"，7.62mm） |
| 供应商设备封装： | 16-DIP |
| 包装： | 管件 |
| 其它名称： | NCV7601PGOS |
NCV7601
TYPICAL PERFORMANCE CHARACTERISTICS
1.37
1.36
1.35
1.34
1.33
1.32
1.31
1.30
1.29
I OUT = 100 mA
I OUT = 10 mA
1.28
-40
-20
0
20 40 60 80
100
120
140
Temperature ( ° C)
Figure 9. Typical Input Threshold Voltage, V CC = 5.0 V
DETAILED OPERATING DESCRIPTION
The NCV7601 Quad Driver consists of four identical
driver sections with output clamp diodes and a common bias
generator.
Each driver input (Figure 2) is buffered by a PNP emitter
follower for reduced input bias current and features a nominal
18 V Zener input clamp for transient protection. Each input
is compared to a separate temperature-compensated
reference, which provides a nominal 1.35 V comparison
threshold. With the addition of an external series resistor, the
inputs can be interfaced directly to +14 V automotive system
voltages. Floating inputs are interpreted as high.
Each driver output NPN is supplied with a substantially
fixed base current from the +5.0 V V CC pin by a pre-driver.
Each pre-driver multiplies a temperature-compensated
reference current when its control input and the common
enable input is high. Current limit and thermal limit circuits
act independently within the pre-driver to reduce base drive
to the output NPN. The independent limit operation allows
the driver to handle inrush current from lamp loads while
protecting the driver from fault conditions that exist long
enough to raise the temperature at that driver to its thermal
limit threshold. Each driver has its own
temperature-sensing device located in close proximity to
the output NPN. The separate sensing devices are
strategically placed at the corners of the die to reduce
interaction between them.
APPLICATIONS INFORMATION
The NCV7601 Quad Driver interfaces high power loads
to low power control signals. The four open-collector
NAND drivers with common ENABLE are TTL, DTL and
CMOS compatible. Any number of drivers may be parallel
connected to drive loads greater than each driver's nominal
capability. Power for the Quad's control logic and output
pre-drive is supplied from the +5.0 V V CC pin, and is
proportional to the number of active inputs. Minimum
standby power is consumed when the ENABLE input is low.
Each driver is individually protected with current limit and
thermal limit circuitry. Drivers with fault loads are protected
while drivers with normal loads continue to operate,
provided that sufficient heat sinking maintains a good
thermal gradient between all drivers.
Clamp diodes at each driver output provide a means for
managing inductive load transients. The common cathode
pin for each driver pair can be connected to the load supply
voltage for suppression of minor transients resulting from
wiring harness inductances. The use of an external Zener
diode or TVS (Transient Voltage Suppressor) device such as
the ON Semiconductor 1.5SMCXXXAT3 series is strongly
recommended when driving large inductive loads or when
load supply transients can be expected to exceed the Quad
Driver's VCE (SUS) rating. The use of a TVS device provides
an additional benefit by reducing the decay time of inductive
loads. More information on safeguarding the Quad's output
NPN's and about transient suppression methods and device
selection is available in ON Semiconductor application
notes “Understanding Power Transistors Breakdown
Parameters”, document number AN1628/D, “A Review of
Transients and their Means Of Suppression”, document
number AN843/D and “Transient Power Capability of
Zener Diodes”, document number AN784/D. All
application notes are available through the Literature
Distribution Center or via our website at
http://www.onsemi.com.
http://onsemi.com
5
相关PDF资料 |
PDF描述 |
|---|---|
| NCV7608DWR2G | IC DVR LO/HI SIDE 8CH 28-SOIC |
| NCV7702BDWG | IC DRIVER H-BRDG DUAL 1A 24-SOIC |
| NCV7703BD2R2G | IC DVR HALF BRIDGE TRPL 14SOIC |
| NCV7708BDWR2G | IC DRIVER HALF BRIDGE HEX 28SOIC |
| NCV7809BD2TR4G | IC REG POS 9V 1A D2PAK-3 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| NCV7608 | 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:Octal Configurable Low/High Side Driver |
| NCV7608DQR2G | 制造商:ON Semiconductor 功能描述:8 CHANNEL DRIVER - Tape and Reel 制造商:ON Semiconductor 功能描述:IC DVR LO/HI SIDE 8CH 制造商:ON Semiconductor 功能描述:REEL / 8 CHANNEL DRIVER |
| NCV7608DWR2G | 功能描述:功率驱动器IC 8 CHANNEL DRIVER RoHS:否 制造商:Micrel 产品:MOSFET Gate Drivers 类型:Low Cost High or Low Side MOSFET Driver 上升时间: 下降时间: 电源电压-最大:30 V 电源电压-最小:2.75 V 电源电流: 最大功率耗散: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Tube |
| NCV7680 | 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:Linear Current Regulator and Controller for Automotive LED Rear Combination Lamps |
| NCV7680PWR22GEVB | 功能描述:LED 照明开发工具 NCV7680 EVB 2 RoHS:否 制造商:Fairchild Semiconductor 产品:Evaluation Kits 用于:FL7732 核心: 电源电压:120V 系列: 封装: |
发布紧急采购，3分钟左右您将得到回复。