- 您现在的位置：买卖IC网 > PDF目录19222 > NCV8141D2TR4 (ON Semiconductor)IC REG LDO 5V .5A D2PAK-7 PDF资料下载
参数资料
| 型号： | NCV8141D2TR4 |
| 厂商： | ON Semiconductor |
| 文件页数： | 6/13页 |
| 文件大小： | 0K |
| 描述： | IC REG LDO 5V .5A D2PAK-7 |
| 产品变化通告： | LTB Notification 03/Jan/2008 |
| 标准包装： | 750 |
| 稳压器拓扑结构： | 正，固定式 |
| 输出电压： | 5V |
| 输入电压： | 7 V ~ 26 V |
| 电压 - 压降（标准）： | 1.25V @ 500mA |
| 稳压器数量： | 1 |
| 电流 - 输出： | 500mA |
| 电流 - 限制（最小）： | 600mA |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | TO-263-8，D²Pak（7 引线+接片），TO-263CA |
| 供应商设备封装： | D2PAK-7 |
| 包装： | 带卷 (TR) |
NCV8141
DEFINITION OF TERMS
Dropout Voltage: The input ? output voltage differential
at which the circuit ceases to regulate against further
reduction in input voltage. Measured when the output
voltage has dropped 100 mV from the nominal value
obtained at 14 V input, dropout voltage is dependent upon
load current and junction temperature.
Input Voltage: The DC voltage applied to the input
terminals with respect to ground.
Line Regulation: The change in output voltage for a
change in the input voltage. The measurement is made under
conditions of low dissipation or by using pulse techniques
such that the average chip temperature is not significantly
affected.
Load Regulation: The change in output voltage for a
change in load current at constant chip temperature.
Quiescent Current: The part of the positive input current
that does not contribute to the positive load current. The
regulator ground lead current.
Ripple Rejection: The ratio of the peak ? to ? peak input
ripple voltage to the peak ? to ? peak output ripple voltage.
Current Limit: Peak current that can be delivered to the
output.
CIRCUIT DESCRIPTION
The NCV8141 is a 5.0 V Watchdog Regulator with
protection circuitry and three logic control functions that
allow a microprocessor to control its own power supply. The
NCV8141 is designed for use in automotive, switch mode
power supply post regulator, and battery powered systems.
Basic regulator performance characteristics include a low
noise, low drift, 5.0 V ± 3.0% precision output voltage with
low dropout voltage (1.25 V @ I OUT = 500 mA) and low
quiescent current (7.0 mA @ I OUT = 500 mA). On board
short circuit, thermal, and overvoltage protection make it
possible to use this regulator in particularly harsh operating
environments.
The Watchdog logic function monitors an input signal
(WDI) from the microprocessor or other signal source.
When the signal frequency goes below the externally
programmable limit, a RESET signal is generated (RESET).
Proper operation has been verified at a frequency up to 100
kHz. No abnormal RESET signals will occur with
frequencies lower than 100 kHz and the maximum
Threshold Frequency (96 Hz). An external capacitor
(C DELAY ) programs the watchdog frequency limit as well as
the power on reset (POR) and RESET delay.
The RESET function is activated by any of three
conditions: the watchdog signal moves outside of its preset
limits; the output voltage drops out of regulation b y more
than 4.5%; or the IC is in its power up sequence. The RESET
signal is independent of V IN and reliable down to V OUT =
1.0 V.
In conjunction with the Watchdog, the ENABLE
function controls the regulator ’s power consumption. The
NCV8141’s output stage and its attendant circuitry are
enabled by setting the ENABLE lead high. The regulator
goes into sleep mode when the ENABLE lead goes low and
the watchdog signal moves outside its preset limit. This
unique combination of control functions in the NCV8141
gives the microprocessor control over its own power down
VOLTAGE REFERENCE AND OUTPUT CIRCUITRY
Precision Voltage Reference
The regulated output voltage depends on the precision band
gap voltage reference in the IC. By adding an error amplifier
into the feedback loop, the output voltage is maintained within
± 3.0% over temperature and supply variation.
Output Stage
The composite PNP ? NPN output structure (Figure 7)
provides 500 mA (min) of output current while maintaining
a low drop out voltage (1.25 V) and drawing little quiescent
current (7.0 mA).
V IN
V OUT
Figure 7. Composite Output Stage of the NCV8141
The NPN pass device prevents deep saturation of the
output stage which in turn improves the IC’s efficiency by
preventing excess current from being used and dissipated by
the IC.
Output Stage Protection
The output stage is protected against overvoltage, short
circuit and thermal runaway conditions (Figure 8).
If the input voltage rises above 30 V (e.g. load dump), the
output shuts down. This response protects the internal
circuitry and enables the IC to survive unexpected voltage
transients.
sequence: i.e. it gives the microprocessor the flexibility to
perform housekeeping functions before it powers down.
http://onsemi.com
6
相关PDF资料 |
PDF描述 |
|---|---|
| GMC44DRAI-S734 | CONN EDGECARD 88POS .100 R/A SLD |
| VE-B0W-CX-S | CONVERTER MOD DC/DC 5.5V 75W |
| TH3B105K035D4400 | CAP TANT 1UF 35V 10% 1411 |
| LM4040A25IDBZR | IC VREF SHUNT PREC 2.5V SOT-23-3 |
| NCV8501DADJG | IC REG LDO ADJ .15A 8-SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| NCV8141D2TR4G | 功能描述:低压差稳压器 - LDO ANA WATCHDOG REG RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| NCV8184 | 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:Micropower 70 mA Low Dropout Tracking Regulator/Line Driver |
| NCV8184/D | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Micropower 70mA Low Dropout Tracking Regulator / Line Driver |
| NCV8184_06 | 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:Micropower 70 mA Low Dropout Tracking Regulator/Line Driver |
| NCV8184D | 功能描述:低压差稳压器 - LDO 70mA Tracking RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
发布紧急采购，3分钟左右您将得到回复。