- 您现在的位置：买卖IC网 > PDF目录19222 > NCV8501D50 (ON Semiconductor)IC REG LDO 5V .15A 8-SOIC PDF资料下载
参数资料
| 型号： | NCV8501D50 |
| 厂商： | ON Semiconductor |
| 文件页数： | 10/16页 |
| 文件大小： | 0K |
| 描述： | IC REG LDO 5V .15A 8-SOIC |
| 产品变化通告： | Product Discontinuation 27/Jun/2007 |
| 标准包装： | 98 |
| 稳压器拓扑结构： | 正，固定式 |
| 输出电压： | 5V |
| 输入电压： | 最高 45 V |
| 电压 - 压降（标准）： | 0.4V @ 150mA |
| 稳压器数量： | 1 |
| 电流 - 输出： | 150mA |
| 电流 - 限制（最小）： | 151mA |
| 工作温度： | -40°C ~ 150°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 8-SOICN |
| 包装： | 管件 |
NCV8501 Series
CIRCUIT DESCRIPTION
REGULATOR CONTROL FUNCTIONS
The NCV8501 contains the microprocessor compatible
control function RESET (Figure 14).
V IN
The DELAY lead provides source current (typically 2.5 m A)
to the external DELAY capacitor during the following
proceedings:
1. During Power Up (once the regulation threshold
has been verified).
2. After a reset event has occurred and the device is
back in regulation. The DELAY capacitor is
V OUT
DELAY
RESET
RESET
Threshold
DELAY
Threshold
(V DT )
discharged when the regulation (RESET threshold)
has been violated. This is a latched incident. The
capacitor will fully discharge and wait for the
device to regulate before going through the delay
time event again.
T d T d
Figure 14. Reset and Delay Circuit Wave Forms
RESET Function
A RESET signal (low voltage) is generated as the IC
powers up until V OUT is within 6.0% of the regulated output
voltage, or when V OUT drops out of regulation,and is lower
than 8.0% below the regulated output voltage. Hysteresis is
included in the function to minimize oscillations.
The RESET output is an open collector NPN transistor,
controlled by a low voltage detection circuit. The circuit is
functionally independent of the rest of the IC thereby
FLAG/Monitor Function
An on ? chip comparator is provided to perform an early
warning to the microprocessor of a possible reset signal. The
reset signal typically turns the microprocessor off
instantaneously. This can cause unpredictable results with
the microprocessor. The signal received from the FLAG pin
will allow the microprocessor time to complete its present
task before shutting down. This function is performed by a
comparator referenced to the bandgap reference. The actual
trip point can be programmed externally using a resistor
divider to the input monitor (MON) (Figure 16). The typical
threshold is 1.20 V on the MON pin.
guaranteeing that the RESET signal is valid for V OUT as low
as 1.0 V.
V BAT
V IN
V OUT
V CC
ENABLE Function
The part stays in a low I Q sleep mode when the ENABLE
pin is held low. The part has an internal pull down if the pin
NCV8501
MON FLAG
C OUT
I/O
m P
is left floating. This is intended for failure modes only. An
external connection (active pulldown, resistor, or switch) for
normal operation is recommended.
The integrity of the ENABLE pin allows it to be tied
R ADJ RESET
DELAY GND
RESET
directly to the battery line through an external resistor. It will
withstand load dump potentials in this configuration.
Figure 16. FLAG/Monitor Function
Voltage Adjust
V BAT
10 k
V IN
NCV8501
V OUT
Figure 17 shows the device setup for a user configurable
output voltage. The feedback to the V ADJ pin is taken from
a voltage divider referenced to the output voltage. The loop
is balanced around the Unity Gain threshold (1.28 V
ENABLE
typical).
GND
V OUT
≈ 5.0 V
Figure 15. ENABLE Function
NCV8501
15 k
C OUT
DELAY Function
The reset delay circuit provides a programmable (by
V ADJ
1.28 V
5.1 k
external capacitor) delay on the RESET output lead.
Figure 17. Adjustable Output Voltage
http://onsemi.com
10
相关PDF资料 |
PDF描述 |
|---|---|
| MIC2845A-PGYMT TR | IC WHITE LED DVR 6CH BKLT 14TMLF |
| NCV8501D33G | IC REG LDO 3.3V .15A 8-SOIC |
| NCV8501D33 | IC REG LDO 3.3V .15A 8-SOIC |
| LM4040A30IDBZR | IC VREF SHUNT PREC 3V SOT-23-3 |
| AIML-1206-R27K-T | INDUCTOR MULTILAYER 0.27UH 1206 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| NCV8501D50G | 功能描述:低压差稳压器 - LDO 5.0V 150mA w/ENABLE RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| NCV8501D50R2 | 功能描述:低压差稳压器 - LDO 5.0V 150mA w/ENABLE RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| NCV8501D50R2G | 功能描述:低压差稳压器 - LDO 5.0V 150mA w/ENABLE RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| NCV8501D80 | 功能描述:低压差稳压器 - LDO 8.0V 150mA w/ENABLE RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| NCV8501D80G | 功能描述:低压差稳压器 - LDO 8.0V 150mA w/ENABLE RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
发布紧急采购，3分钟左右您将得到回复。