- 您现在的位置：买卖IC网 > PDF目录19216 > NCV8506D2T50 (ON Semiconductor)IC REG LDO 5V .4A D2PAK-7 PDF资料下载
参数资料
| 型号： | NCV8506D2T50 |
| 厂商： | ON Semiconductor |
| 文件页数： | 9/12页 |
| 文件大小： | 0K |
| 描述： | IC REG LDO 5V .4A D2PAK-7 |
| 产品变化通告： | Product Discontinuation 27/Jun/2007 |
| 标准包装： | 50 |
| 稳压器拓扑结构： | 正，固定式 |
| 输出电压： | 5V |
| 输入电压： | 最高 45 V |
| 电压 - 压降（标准）： | 0.4V @ 400mA |
| 稳压器数量： | 1 |
| 电流 - 输出： | 400mA |
| 电流 - 限制（最小）： | 425mA |
| 工作温度： | -40°C ~ 150°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | TO-263-8，D²Pak（7 引线+接片），TO-263CA |
| 供应商设备封装： | D2PAK-7 |
| 包装： | 管件 |
NCV8506 Series
CIRCUIT DESCRIPTION
REGULATOR CONTROL FUNCTIONS
The NCV8506 contains the microprocessor compatible
control function RESET (Figure 13).
V IN
The DELAY lead provides source current (typically 4.0 m A)
to the external DELAY capacitor during the following
proceedings:
1. During Power Up (once the regulation threshold
has been verified).
2. After a reset event has occurred and the device is
back in regulation. The DELAY capacitor is
V OUT
DELAY
RESET
RESET
Threshold
DELAY
Threshold
(V DT )
discharged when the regulation (RESET threshold)
has been violated. This is a latched incident. The
capacitor will fully discharge and wait for the
device to regulate before going through the delay
time event again.
V OUT
T d T d
Figure 13. Reset and Delay Circuit Wave Forms
RESET Function
A RESET signal (low voltage) is generated as the IC
powers up until V OUT is within 1.5% of the regulated output
voltage, or when V OUT drops out of regulation,and is lower
than 4.0% below the regulated output voltage. Hysteresis is
included in the function to minimize oscillations.
The RESET output is an open collector NPN transistor,
Voltage Adjust
Figure 14 shows the device setup for a user configurable
output voltage. The feedback to the V ADJ pin is taken from
a voltage divider referenced to the output voltage. The loop
is balanced around the Unity Gain threshold (1.30 V
typical).
≈ 5.0 V
NCV8506 15 k C OUT
controlled by a low voltage detection circuit. The circuit is
functionally independent of the rest of the IC thereby
guaranteeing that the RESET signal is valid for V OUT as low
as 1.0 V.
DELAY Function
V ADJ
1.28 V
5.1 k
The reset delay circuit provides a programmable (by
external capacitor) delay on the RESET output lead.
APPLICATION NOTES
Figure 14. Adjustable Output
Voltage
SETTING THE DELAY TIME
The delay time is controlled by the Reset Delay Low
Voltage, Delay Switching Threshold, and the Delay Charge
Current. The delay follows the equation:
STABILITY CONSIDERATIONS
The output or compensation capacitor helps determine
three main characteristics of a linear regulator: start ? up
delay, load transient response and loop stability.
tDELAY +
CDELAY(Vdt * Reset Delay Low Voltage)
Delay Charge Current
The capacitor value and type should be based on cost,
availability, size and temperature constraints. A tantalum or
aluminum electrolytic capacitor is best, since a film or
Example:
Using C DELAY = 33 nF.
Assume reset Delay Low Voltage = 0.
Use the typical value for V dt = 1.8 V (2.5 V, 3.3 V, and
5.0 V options).
Use the typical value for Delay Charge Current = 4.2 m A.
ceramic capacitor with almost zero ESR can cause
instability. The aluminum electrolytic capacitor is the least
expensive solution, but, if the circuit operates at low
temperatures ( ? 25 ° C to ? 40 ° C), both the value and ESR of
the capacitor will vary considerably. The capacitor
manufacturers data sheet usually provides this information.
tDELAY +
33 nF(1.8 * 0)
4.2 m A
+ 14 ms
http://onsemi.com
9
相关PDF资料 |
PDF描述 |
|---|---|
| ABM36DTKT-S288 | CONN EDGECARD EXTEND 72POS .156 |
| TAJV158K002RNJ | CAP TANT 1500UF 2.5V 10% 2924 |
| TAJV157K020RNJ | CAP TANT 150UF 20V 10% 2924 |
| R-745.0P | CONV DC/DC 4A 5.0V OUT VERT SIP |
| FSM18DSEI-S13 | CONN EDGECARD 36POS .156 EXTEND |
相关代理商/技术参数 |
参数描述 |
|---|---|
| NCV8506D2T50G | 功能描述:低压差稳压器 - LDO ANA MICROPOWER 400 RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| NCV8506D2T50R4 | 功能描述:低压差稳压器 - LDO 5.0V 400mA w/ENABLE RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| NCV8506D2T50R4G | 功能描述:低压差稳压器 - LDO ANA MICROPOWER 400 RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| NCV8506D2TADJ | 功能描述:低压差稳压器 - LDO 400mA ADJ w/ENABLE RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| NCV8506D2TADJG | 功能描述:低压差稳压器 - LDO ANA MICROPOWER 400 RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
发布紧急采购，3分钟左右您将得到回复。