参数资料
型号: NCV8508DW50G
厂商: ON Semiconductor
文件页数: 9/26页
文件大小: 0K
描述: IC REG LDO 5V 16SOIC
标准包装: 47
稳压器拓扑结构: 正,固定式
输出电压: 5V
输入电压: 最高 45 V
电压 - 压降(标准): 0.45V @ 150mA
稳压器数量: 1
电流 - 限制(最小): 250mA
工作温度: -40°C ~ 125°C
安装类型: 表面贴装
封装/外壳: 16-SOIC(0.295",7.50mm 宽)
供应商设备封装: 16-SOIC W
包装: 管件
NCV8508
CIRCUIT DESCRIPTION
Functional Description
To reduce the drain on the battery, a system can go into a
low current consumption mode whenever it is not
performing a main routine. The Wakeup signal is generated
continuously and is used to interrupt a microcontroller that
is in sleep mode. The nominal output is a 5.0 volt square
wave (voltage generated from V OUT ) with a duty cycle of
50% at a frequency that is determined by a timing resistor,
R Delay .
When the microprocessor receives a rising edge from the
Wakeup output, it must issue a Watchdog pulse and check its
inputs to decide if it should resume normal operations or
remain in the sleep mode.
The first falling edge of the Watchdog signal causes the
Wakeup to go low within 2.0 m s (typ) and remain low until
the next Wakeup cycle (see Figure 17). Other Watchdog
pulses received within the same cycle are ignored (Figure 3).
During power up, RESET is held low until the output
voltage is in regulation. During operation, if the output
voltage shifts below the regulation limits, the RESET
toggles low and remains low until proper output voltage
regulation is restored. After the RESET delay, RESET
returns high.
The Watchdog circuitry continuously monitors the input
Watchdog signal (WDI) from the microprocessor. The
absence of a falling edge on the Watchdog input during one
Wakeup cycle will cause a RESET pulse to occur at the end
of the Wakeup cycle. (see Figure 4).
The Wakeup output is pulled low during a RESET
regardless of the cause of the RESET. After the RESET
returns high, the Wakeup cycle begins again (see Figure 4).
The RESET Delay Time, Wakeup signal frequency and
RESET high to Wakeup delay time are all set by one external
resistor R Delay .
Wakeu p Period = (4.17 × 10 ? 7 )R Delay
RESE T Delay Time = (5.21 × 10 ? 8 )R Delay
RESET HIGH to Wakeup Delay Time = (2.08 × 10 ? 7 )R Delay
Resistor temperature coefficient and tolerance as well as
the tolerance of the NCV8508 must be taken into account in
order to get the correct system tolerance for each parameter.
WDI
Wakeup
Wakeup
Response
to WDI
Figure 17. Wakeup Response to WDI
RESET
Wakeup
Wakeup
Response
to RESET
Figure 18. Wakeup Response to RESET (Low
Voltage)
http://onsemi.com
9
相关PDF资料
PDF描述
GCA18DCBS CONN EDGECARD 36POS R/A .125 SLD
REC8-1205SRW/H3/A/M CONV DC/DC 8W 12VIN 05VOUT
EMC44DRTI-S93 CONN EDGECARD 88POS DIP .100 SLD
TAP107M016CRW CAP TANT 100UF 16V 20% RADIAL
F930J107MAA CAP TANT 100UF 6.3V 20% SMD
相关代理商/技术参数
参数描述
NCV8508DW50R2 功能描述:低压差稳压器 - LDO 5V 250mA w/WatchDog RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压(最大值):307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20
NCV8508DW50R2G 功能描述:低压差稳压器 - LDO 5V 250mA w/WatchDog RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压(最大值):307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20
NCV8508PD50 功能描述:低压差稳压器 - LDO 5V 250mA w/WatchDog RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压(最大值):307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20
NCV8508PD50G 功能描述:低压差稳压器 - LDO 5V 250mA w/WatchDog Reset RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压(最大值):307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20
NCV8508PD50R2 功能描述:低压差稳压器 - LDO 5V 250mA w/WatchDog RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压(最大值):307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20