参数资料
| 型号： | NCV8518PWG |
| 厂商： | ON Semiconductor |
| 文件页数： | 10/12页 |
| 文件大小： | 0K |
| 描述： | IC REG LDO 5V .25A 16-SOIC |
| 标准包装： | 47 |
| 稳压器拓扑结构： | 正，固定式 |
| 输出电压： | 5V |
| 输入电压： | 6 V ~ 28 V |
| 电压 - 压降（标准）： | 0.425V @ 150mA |
| 稳压器数量： | 1 |
| 电流 - 输出： | 250mA |
| 电流 - 限制（最小）： | 255mA |
| 工作温度： | -40°C ~ 150°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-SOIC（0.295"，7.50mm 宽）裸露焊盘 |
| 供应商设备封装： | 16-SOIC W |
| 包装： | 管件 |
NCV8518
OPERATING DESCRIPTION
General
The NCV8518 is a precision micropower voltage
regulator featuring low quiescent current (100 m A typical at
250 mA load) and low dropout voltage (450 mV typical at
150 mA). Integrated microprocessor control functions
include Watchdog, Wakeup and RESET. An Enable input is
provided for logic level control of the regulator state. The
combination of low quiescent current and comprehensive
microprocessor interface functions make the NCV8518
ideal for use in both battery operated and automotive
applications.
The NCV8518 is internally protected against short circuit
and thermal runaway conditions. No external components
are required to engage these protective mechanisms. The
device continues to operate through 45 volt input transients,
an important consideration in automotive environments.
Wakeup and Watchdog
To reduce battery drain, a microprocessor or
microcontroller can transition to a low current consumption
(“sleep”) mode when code execution is suspended or
complete. The NCV8518 Wakeup signal is generated and
output periodically to interrupt sleep mode. The nominal
Wakeup output is a 5 volt square wave (generated from
VOUT) with a duty cycle of 50%, at a frequency determined
by external timing resistor R DELAY . In response to the rising
edge of the Wakeup signal, the microprocessor will
subsequently output a Watchdog pulse and check its inputs
to decide if it should resume normal operation or remain in
sleep mode.
The NCV8518 responds to the falling edge of the
Watchdog signal, which it expects at least once during each
Wakeup period. When the correct Watchdog signal is
received, the Wakeup output is forced low. Other Watchdog
pulses received within the same cycle are ignored. The
Watchdog circuitry continuously monitors the input
Watchdog signal (WDI) from the microprocessor. The
absence of a falling edge on the Watchdog input during one
Wakeup cycle will cause a Reset pulse to be output at the end
of the Wakeup cycle (see Figure 4).
RESET
As output voltage falls, the RESET output will maintain
its current state down to V OUT = 1 V. A Reset signal (active
low) is asserted for any of four conditions:
1. During power up, RESET is held low until the
output voltage is in regulation.
2. During operation, if the output voltage falls below
the Reset threshold, RESET switches low, and will
remain low until both the output voltage has
recovered and the Reset delay timer cycle has
completed following that recovery.
3. RESET will switch low if the regulator does not
receive a Watchdog input signal within a Wakeup
period.
4. Regardless of output voltage, RESET will switch
low if the regulator input voltage V IN , falls below
a level required to sustain the internal control
circuits. The specific voltage is temperature
dependent, and is approximately 4.75 V at 20 ° C.
The Wakeup output is pulled low during a RESET
regardless of the cause of the RESET. After the RESET
returns high, the Wakeup cycle begins again (see Figure 4).
The RESET Delay Time, Wakeup signal frequency and
RESET high to Wakeup delay time are all set by one external
resistor, RDelay, according to the following equations:
Wakeup Period (seconds) = (4.17 10 ? 7 ) * R DELAY ( W )
RESET Delay Time (seconds) = (5.21 10 ? 8 ) * R DELAY ( W )
RESET High to Wakeup Delay Time (seconds) =
(2.08 10 ? 7 ) * R DELAY ( W )
The voltage present at the Delay pin is a buffered bandgap
voltage (~1.25 V) and can be used as a reference for an
external tracking regulator.
Enable
This is a standard TTL and CMOS logic compatible input
that can be used to turn the regulator on or off. Logic high
enables the regulator; logic low disables it (also called
shutdown ). In the disabled/shutdown state, the pass
transistor is off and total quiescent current is less than 1 m A.
V BAT
C1*
0.1 m F
V IN
V OUT
C2
1.0 m F
V DD
WDI
I/O
NCV8518
OK
Fault
Delay
RESET
WAKE UP
RESET
I/O
R Delay
120 k
GND
ENABLE
OFF
ON
*C1 required if regulator is located far from power supply filter.
Figure 17. Application Circuit
http://onsemi.com
10
相关PDF资料 |
PDF描述 |
|---|---|
| NCV8535MNADJR2G | IC REG LDO ADJ .7A 10-DFN |
| NCV8537MN500R2G | IC REG LDO 5V .7A 10-DFN |
| NCV8570BMN300R2G | IC REG LDO 3V .2A 6DFN |
| NCV8570BSN25T1G | IC REG LDO 2.5V .2A 5TSOP |
| NCV8570MN330R2G | IC REG LDO 3.3V .2A 6-DFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| NCV8518PWR2G | 功能描述:低压差稳压器 - LDO LINEAR VOLTAGE REG RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| NCV8535 | 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:Ultra High Accuracy, Low Iq, 500 mA Low Dropout Regulator with Enable |
| NCV8535MN150R2G | 功能描述:低压差稳压器 - LDO 500mA LDO AUTO VERSN RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| NCV8535MN180R2G | 功能描述:低压差稳压器 - LDO 500mA LDO AUTO VERSN RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| NCV8535MN190R2G | 功能描述:低压差稳压器 - LDO 500MA LDO AUTO VERSION RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
发布紧急采购，3分钟左右您将得到回复。