- 您现在的位置：买卖IC网 > PDF目录20153 > NCV8702SN18T1G (ON Semiconductor)IC REG LDO 1.8V .2A SOT23-5 PDF资料下载
参数资料
| 型号： | NCV8702SN18T1G |
| 厂商： | ON Semiconductor |
| 文件页数： | 15/20页 |
| 文件大小： | 0K |
| 描述： | IC REG LDO 1.8V .2A SOT23-5 |
| 标准包装： | 3,000 |
| 稳压器拓扑结构： | 正，固定式 |
| 输出电压： | 1.8V |
| 输入电压： | 最高 5.5V |
| 电压 - 压降（标准）： | 0.14V @ 200mA |
| 稳压器数量： | 1 |
| 电流 - 输出： | 200mA |
| 电流 - 限制（最小）： | 220mA |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 6-TSSOP（5 引线），SC-88A，SOT-353 |
| 供应商设备封装： | 5-TSOP |
| 包装： | 带卷 (TR) |
NCV8702
APPLICATIONS INFORMATION
General
The NCV8702 is a high performance 200 mA Low
Dropout Linear Regulator. This device delivers excellent
noise and dynamic performance.
Thanks to its adaptive ground current feature the device
consumes only 10 m A of quiescent current at no ? load
condition.
The regulator features ultra ? low noise of 11 m V RMS ,
PSRR of 68 dB at 1 kHz and very good load/line transient
performance. Such excellent dynamic parameters and small
package size make the device an ideal choice for powering
the precision analog and noise sensitive circuitry in portable
applications. The LDO achieves this ultra low noise level
output without the need for a noise bypass capacitor.
A logic EN input provides ON/OFF control of the output
voltage. When the EN is low the device consumes as low as
typ. 10 nA from the IN pin.
The LDO achieves ultra ? low output voltage noise without
the need for additional noise bypass capacitor.
The device is fully protected in case of output overload,
output short circuit condition and overheating, assuring a
very robust design.
Input Capacitor Selection (C IN )
It is recommended to connect a minimum of 1 m F Ceramic
X5R or X7R capacitor close to the IN pin of the device. This
capacitor will provide a low impedance path for unwanted
AC signals or noise modulated onto constant input voltage.
There is no requirement for the min./max. ESR of the
input capacitor but it is recommended to use ceramic
capacitors for their low ESR and ESL. A good input
capacitor will limit the influence of input trace inductance
and source resistance during sudden load current changes.
Larger input capacitor may be necessary if fast and large
load transients are encountered in the application.
Output Decoupling (C OUT )
The NCV8702 is designed to be stable with a small 1.0 m F
ceramic capacitor on the output. To assure proper operation
it is strongly recommended to use min. 1.0 m F capacitor with
the initial tolerance of ? 10%, made of X7R or X5R dielectric
material types.
There is no requirement for the minimum value of
Equivalent Series Resistance (ESR) for the C OUT but the
maximum value of ESR should be less than 700 m W .
Larger output capacitors could be used to improve the load
transient response or high frequency PSRR as shown in
typical characteristics. The initial tolerance requirements
can be wider than ? 10% when using capacitors larger than
1 m F.
It is not recommended to use tantalum capacitors on the
output due to their large ESR. The equivalent series
resistance of tantalum capacitors is also strongly dependent
on the temperature, increasing at low temperature. The
tantalum capacitors are generally more costly than ceramic
capacitors.
The table on this page lists the capacitors which were used
during the IC evaluation.
No ? load Operation
The regulator remains stable and regulates the output
voltage properly within the ? 2% tolerance limits even with
no external load applied to the output.
V IN
2 V ... 5.5 V
C1
IN OUT
NCV8702
EN
GND
V OUT
0 mA ... 200 mA
C2
U1
Figure 61. Typical Applications Schematics
LIST OF RECOMMENDED CAPACITORS:
Symbol
C1, C2
Manufacturer
Kemet
TDK
Murata
AVX
Multicomp
Panason ? ECG
Part Number
C0402C105K8PACTU
C1005X5R1A105K
GRM155R61A105KE15D
0402ZD105KAT2A
MCCA000571
ECJ ? 0EB0J475M
Description
1 m F Ceramic ? 10%, 10 V, 0402, X5R
? || ?
? || ?
? || ?
1 m F Ceramic ? 10%, 50 V, 1206, X7R
4.7 m F Ceramic ? 20%, 6.3 V, 0402, X5R
http://onsemi.com
15
相关PDF资料 |
PDF描述 |
|---|---|
| AMM15DRSI-S288 | CONN EDGECARD 30POS .156 EXTEND |
| RMM28DTMT-S189 | CONN EDGECARD 56POS R/A .156 SLD |
| TAJT476K006RNJ | CAP TANT 47UF 6.3V 10% 1210 |
| TPSB155K035R2500 | CAP TANT 1.5UF 35V 10% 1210 |
| TPSB335K025R2000 | CAP TANT 3.3UF 25V 10% 1210 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| NCV8702SN28T1G | 功能描述:低压差稳压器 - LDO 200 MA LDO ULTRA-LOW IQ RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| NCV8702SN30T1G | 功能描述:低压差稳压器 - LDO 200 MA LDO ULTRA-LOW IQ RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| NCV8702SN33T1G | 功能描述:低压差稳压器 - LDO 200 MA LDO ULTRA-LOW IQ RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| NCV8703 | 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:300 mA, Ultra-Low Quiescent Current, IQ 12 A, Ultra-Low Noise, LDO Voltage Regulator |
| NCV8703MX18TCG | 制造商:ON Semiconductor 功能描述:300 MA LDO ULTRA-LOW IQ - Tape and Reel 制造商:ON Semiconductor 功能描述:REEL / 300 MA LDO ULTRA-LOW IQ |
发布紧急采购，3分钟左右您将得到回复。