- 您现在的位置：买卖IC网 > PDF目录17368 > NCV8842MNR2GEVB (ON Semiconductor)BOARD EVAL FOR NCV8842 PDF资料下载
参数资料
| 型号： | NCV8842MNR2GEVB |
| 厂商： | ON Semiconductor |
| 文件页数： | 8/16页 |
| 文件大小： | 0K |
| 描述： | BOARD EVAL FOR NCV8842 |
| 标准包装： | 1 |
| 主要目的： | DC/DC，步降 |
| 稳压器拓扑结构： | 降压 |
| 板类型： | 完全填充 |
| 已供物品： | 板 |
| 已用 IC / 零件： | NCV8842 |
| 其它名称： | NCV8842MNR2GEVBOS |
NCV8842
oscillation, as shown in Figure 8. Similar to current mode
control, this oscillation occurs at the duty cycle greater than
50% and can be alleviated by using a larger inductor value.
The current limit threshold is reduced to Foldback Current
when the FB pin falls below Foldback Threshold. This
feature protects the IC and external components under the
power up or over ? load conditions.
30
25
20
15
10
5
0
0
0.5 1.0
1.5
SWITCHING CURRENT (A)
Figure 9. The Boost Pin Current Includes 7.0 mA
Pre ? Driver Current and Base Current when the
Switch is Turned On. The Beta Decline of the
Power Switch Further Increases the Base
Current at High Switching Current
Shutdown
The internal power switch will not turn on until the V IN
pin rises above the Startup Voltage. This ensures no
Figure 8. The Regulator in Current Limit
BOOST Pin
The BOOST pin provides base driving current for the
switching will occur until adequate supply voltage is
provided to the IC. Refer to Figure 10 for the SHDNB
(shutdown ? bar) pin input circuit.
power switch. A voltage higher than V IN provides required
headroom to turn on the power switch. This in turn reduces
IC power dissipation and improves overall system
efficiency. The BOOST pin can be connected to an external
SHDNB
20k
± 33%
V IN
boost ? strapping circuit which typically uses a 0.1 m F capacitor
and a 1N914 or 1N4148 diode, as shown in Figure 1. When
the power switch is turned on, the voltage on the BOOST pin
is equal to
1.2V
-
+
VBOOST + VIN ) VO * VF
where:
V F = diode forward voltage.
The anode of the diode can be connected to any DC
voltage as well as the regulated output voltage (Figure 1).
However, the maximum voltage on the BOOST pin should
not exceed 40 V.
As shown in Figure 9, the BOOST pin current includes a
constant 7.0 mA pre ? driver current and base current
proportional to switch conducting current. A detailed
discussion of this current is conducted in Thermal
V Z = 6V to 8V
GND
Figure 10.
The IC enters a sleep mode when the SHDNB pin is pulled
below the Shutdown Threshold Voltage. In sleep mode, the
power switch is kept open and the supply current reduces to
Shutdown Quiescent Current ( 1 m A typically). This pin has
an internal pull ? down current. When not in use, pull this pin
up to V CC with a resistor (See Figure 1). A 100 k W pullup
resistor will ensure safe operation from below 9 V and
during a 40 V load dump condition.
Consideration section. A 0.1 m F capacitor is usually
adequate for maintaining the Boost pin voltage during the on
time.
http://onsemi.com
8
相关PDF资料 |
PDF描述 |
|---|---|
| NCP1597BGEVB | BOARD EVALUATION NCP1597B |
| MIC2545A-1BM | IC SW CURR LIMIT HI SIDE 8-SOP |
| NCP1597AGEVB | BOARD EVALUATION NCP1597A |
| A9CAA-0305F | FLEX CABLE - AFG03A/AF03/AFE03T |
| MIC2506BM | IC SW HIGH SIDE DUAL 1A 8SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| NCV8842PWG | 功能描述:直流/直流开关转换器 1.5A LO VLT BUCK REG RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
| NCV8842PWGEVB | 功能描述:电源管理IC开发工具 NCV8842 EVAL BRD RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| NCV8842PWR2G | 功能描述:直流/直流开关转换器 1.5A LO VLT BUCK REG RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
| NCV8843 | 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:1.5 A, 340 kHz, Buck Regulator with Synchronization Capability |
| NCV8843_10 | 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:1.5 A, 340 kHz, Buck Regulator with Synchronization Capability |
发布紧急采购，3分钟左右您将得到回复。