- 您现在的位置：买卖IC网 > PDF目录13685 > NCV8843MNR2G (ON Semiconductor)IC REG BUCK 1.5A 18DFN PDF资料下载
参数资料
| 型号： | NCV8843MNR2G |
| 厂商： | ON Semiconductor |
| 文件页数： | 9/16页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK 1.5A 18DFN |
| 标准包装： | 1 |
| 类型： | 降压（降压） |
| 输出数： | 1 |
| 输入电压： | 4.5 V ~ 40 V |
| PWM 型： | 混合物 |
| 频率 - 开关： | 340kHz |
| 电流 - 输出： | 1.5A |
| 同步整流器： | 无 |
| 工作温度： | -40°C ~ 150°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 18-VFDFN 裸露焊盘 |
| 包装： | 剪切带 (CT) |
| 供应商设备封装： | 18-DFN（5x6） |
| 其它名称： | NCV8843MNR2GOSCT |
NCV8843
Startup
During power up, the regulator tends to quickly charge up
the output capacitors to reach voltage regulation. This gives
rise to an excessive in ? rush current which can be detrimental
to the inductor, IC and catch diode. In V 2 control , the
compensation capacitor provides Soft ? Start with no need
for extra pin or circuitry. During the power up, the Output
Source Current of the error amplifier charges the
compensation capacitor which forces V C pin and thus output
voltage ramp up gradually. The Soft ? Start duration can be
calculated by
minimum duty cycle by extending the switching cycle. This
protects the IC from overheating, and also limits the power
that can be transferred to the output. The current limit
foldback effectively reduces the current stress on the
inductor and diode. When the output is shorted, the DC
current of the inductor and diode can approach the current
limit threshold. Therefore, reducing the current limit by 40%
can result in an equal percentage drop of the inductor and
diode current. The short circuit waveforms are captured in
Figure 12, and the benefit of the foldback frequency and
current limit is self ? evident.
TSS + C
V CCOMP
ISOURCE
where:
V C = V C pin steady ? state voltage, which is approximately
equal to error amplifier ’s reference voltage.
C COMP = Compensation capacitor connected to the V C pin
I SOURCE = Output Source Current of the error amplifier.
Using a 0.1 m F C COMP , the calculation shows a T SS over
5.0 ms which is adequate to avoid any current stresses.
Figure 11 shows the gradual rise of the V C , V O and envelope
of the V SW during power up. There is no voltage over ? shoot
after the output voltage reaches the regulation. If the supply
voltage rises slower than the V C pin, output voltage may
over ? shoot.
Figure 12. In Short Circuit, the Foldback Current and
Foldback Frequency Limit the Switching Current to
Protect the IC, Inductor and Catch Diode
Thermal Considerations
A calculation of the power dissipation of the IC is always
necessary prior to the adoption of the regulator. The current
drawn by the IC includes quiescent current, pre ? driver
current, and power switch base current. The quiescent
current drives the low power circuits in the IC, which
include comparators, error amplifier and other logic blocks.
Therefore, this current is independent of the switching
current and generates power equal to
WQ + VIN
IQ
Figure 11. The Power Up Transition of NCV8843
Regulator
Short Circuit
When the V FB pin voltage drops below Foldback
Threshold, the regulator reduces the peak current limit by
40% and switching frequency to 1/4 of the nominal
frequency. These features are designed to protect the IC and
external components during over load or short circuit
conditions. In those conditions, peak switching current is
clamped to the current limit threshold. The reduced
switching frequency significantly increases the ripple
current, and thus lowers the DC current. The short circuit can
where:
I Q = quiescent current.
The pre ? driver current is used to turn on/off the power
switch and is approximately equal to 12 mA in worst case.
During steady state operation, the IC draws this current from
the Boost pin when the power switch is on and then receives
it from the V IN pin when the switch is off. The pre ? driver
current always returns to the V SW pin. Since the pre ? driver
current goes out to the regulator ’s output even when the
power switch is turned off, a minimum load is required to
prevent overvoltage in light load conditions. If the Boost pin
voltage is equal to V IN + V O when the switch is on, the power
dissipation due to pre ? driver current can be calculated by
cause the minimum duty cycle to be limited by Minimum
Output Pulse Width. The foldback frequency reduces the
http://onsemi.com
9
相关PDF资料 |
PDF描述 |
|---|---|
| UPM1V220MDD | CAP ALUM 22UF 35V 20% RADIAL |
| MAX6324FUT46+T | IC SUPERVISOR 4.63V SOT23-6 |
| 4448-114L | TOROID POWER HI CURRENT 10UH SMD |
| MAX6324FUT26+T | IC SUPERVISOR 2.63V SOT23-6 |
| 4448R-112M | TOROID PWR HI CURRENT 8.0UH SMD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| NCV8843MNR2GEVB | 功能描述:电源管理IC开发工具 NCV8843 EVAL BRD RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| NCV8843PWG | 功能描述:直流/直流开关转换器 1.5A LO VLT BUCK REG RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
| NCV8843PWR2G | 功能描述:直流/直流开关转换器 16L SOW EPAD RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
| NCV8851 | 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:Automotive Grade Synchronous Buck Controller |
| NCV8851-1DBR2G | 制造商:ON Semiconductor 功能描述:SYNC BUCK CONTROLLER - Tape and Reel 制造商:ON Semiconductor 功能描述:SYNC BUCK CONTROLLER - Cut TR (SOS) 制造商:ON Semiconductor 功能描述:IC REG DL BCK/LINEAR 制造商:ON Semiconductor 功能描述:REEL / SYNC BUCK CONTROLLER |
发布紧急采购，3分钟左右您将得到回复。