- 您现在的位置：买卖IC网 > PDF目录20882 > NDTS0515C (Murata Power Solutions Inc)CONV DC/DC 3W 5VIN 15VOUT DIP24 PDF资料下载
参数资料
| 型号： | NDTS0515C |
| 厂商： | Murata Power Solutions Inc |
| 文件页数： | 2/6页 |
| 文件大小： | 0K |
| 描述： | CONV DC/DC 3W 5VIN 15VOUT DIP24 |
| 产品培训模块： | Low Power DC/DC Converters <5W |
| 标准包装： | 15 |
| 系列： | NDTS |
| 类型： | 隔离 |
| 输出数： | 1 |
| 电压 - 输入（最小）： | 4.5V |
| 电压 - 输入（最大）： | 9V |
| Voltage - Output 1： | 15V |
| 电流 - 输出（最大）： | 200mA |
| 电源（瓦） - 制造商系列： | 3W |
| 电压 - 隔离： | 1kV（1000V） |
| 安装类型： | 通孔 |
| 封装/外壳： | 24-DIP 模块（600 mil，8 引线） |
| 尺寸/尺寸： | 1.27" L x 0.58" W x 0.27" H（32.3mm x 14.7mm x 6.9mm） |
| 包装： | 管件 |
| 工作温度： | -40°C ~ 85°C |
| 效率： | 77% |
| 电源（瓦特）- 最大： | 3W |
| 产品目录页面： | 2716 (CN2011-ZH PDF) |
| 其它名称： | 811-1386-5 |
NDTS Series
Isolated 3W Single Output DC/DC Converters
ABSOLUTE MAXIMUM RATINGS
Short-circuit protection
Lead temperature 1.5mm from case for 10 seconds
Minimum output load for speci?cation 3
Input voltage 05 types
Input voltage 12 types
Input voltage 24 types
Input voltage 48 types
Free air space
GENERAL CHARACTERISTICS
8 Hours
300°C
25% of rated output
10V
20V
40V
80V
10mm Min. around component
Parameter
Switching frequency
Conditions
100% to 25% load, V IN Min. to Max.
Min.
70
Typ.
Max.
650
Units
kHz
ISOLATION CHARACTERISTICS
Parameter
Isolation voltage
Resistance
Conditions
Flash tested for 1 second
Resistance
Min.
1000
1
Typ.
Max.
Units
VDC
GΩ
TEMPERATURE CHARACTERISTICS
Parameter
Conditions
Min.
Typ.
Max.
Units
Operation
Storage
-40
-50
85
125
Case temperature rise above ambient
in still air
NDTS0515C, NDTS1205C, NDTS1212C, NDTS1215C, NDTS2405C,
NDTS2412C, NDTS2415C, NDTS4812C & NDTS4815C
NDTS0505C, NDTS0512C, NDTS1203C, NDTS2403C, NDTS4803C &
NDTS4805C
NDTS0503C
30
40
50
oC
TECHNICAL NOTES
ISOLATION VOLTAGE
‘Hi Pot Test’, ‘Flash Tested’, ‘Withstand Voltage’, ‘Proof Voltage’, ‘Dielectric Withstand Voltage’ & ‘Isolation Test Voltage’ are all terms that relate to the same thing, a test voltage,
applied for a speci?ed time, across a component designed to provide electrical isolation, to verify the integrity of that isolation.
Murata Power Solutions NDTS series of DC/DC converters are all 100% production tested at their stated isolation voltage. This is 1kVDC for 1 second.
A question commonly asked is, “What is the continuous voltage that can be applied across the part in normal operation?”
For a part holding no speci?c agency approvals, such as the NDTS series, both input and output should normally be maintained within SELV limits i.e. less than 42.4V peak, or
60VDC. The isolation test voltage represents a measure of immunity to transient voltages and the part should never be used as an element of a safety isolation system. The part
could be expected to function correctly with several hundred volts offset applied continuously across the isolation barrier; but then the circuitry on both sides of the barrier must
be regarded as operating at an unsafe voltage and further isolation/insulation systems must form a barrier between these circuits and any user-accessible circuitry according to
safety standard requirements.
REPEATED HIGH-VOLTAGE ISOLATION TESTING
It is well known that repeated high-voltage isolation testing of a barrier component can actually degrade isolation capability, to a lesser or greater degree depending on materials,
construction and environment. The NDTS series has an EI ferrite core, with no additional insulation between primary and secondary windings of enameled wire. While parts can be
expected to withstand several times the stated test voltage, the isolation capability does depend on the wire insulation. Any material, including this enamel (typically polyurethane)
is susceptible to eventual chemical degradation when subject to very high applied voltages thus implying that the number of tests should be strictly limited. We therefore strongly
advise against repeated high voltage isolation testing, but if it is absolutely required, that the voltage be reduced by 20% from speci?ed test voltage.
This consideration equally applies to agency recognized parts rated for better than functional isolation where the wire enamel insulation is always supplemented by a further
insulation system of physical spacing or barriers.
RoHS COMPLIANCE INFORMATION
This series is compatible with RoHS soldering systems with a peak wave solder
temperature of 300oC for 10 seconds. The pin termination ?nish on this product series
is Tin. The series is backward compatible with Sn/Pb soldering systems.
For further information, please visit www.murata-ps.com/rohs
www.murata-ps.com/support
KDC_NDTS.D06 Page 2 of 6
相关PDF资料 |
PDF描述 |
|---|---|
| P51-750-S-E-MD-4.5V-000-000 | SENSOR 750PSI 3/8-24 UNF .5-4.5V |
| P51-750-A-G-M12-4.5OVP-000-000 | SENSOR 750PSI 1/8-27NPT .5-4.5V |
| REC3-4812SRWZ/H2/A/CTRL | CONV DC/DC 3W 18-72VIN 12VOUT |
| REC5-2415DRWZ/H4/A/M | CONV DC/DC 5W 9-36VIN +/-15VOUT |
| P51-15-S-U-D-4.5V-000-000 | SENSOR 15PSI 7/16-20-2B .5-4.5V |
相关代理商/技术参数 |
参数描述 |
|---|---|
| NDTS1203C | 功能描述:DC/DC转换器 12Vin 3.3Vout 909mA Isolated 3W 24 pin RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸: |
| NDTS1205C | 功能描述:DC/DC转换器 12Vin 5Vout 600mA Isolated 3W 24 pin RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸: |
| NDTS1212C | 功能描述:DC/DC转换器 12Vin 12Vout 250mA Isolated 3W 24 pin RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸: |
| NDTS1215C | 功能描述:DC/DC转换器 12Vin 15Vout 200mA Isolated 3W 24 pin RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸: |
| NDTS2403 | 功能描述:DC/DC转换器 3W Single Output 24V to 3.3V 909mA RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸: |
发布紧急采购，3分钟左右您将得到回复。