- 您现在的位置：买卖IC网 > PDF目录363338 > NM24C04FLZN (FAIRCHILD SEMICONDUCTOR CORP) I2C Serial EEPROM PDF资料下载
参数资料
| 型号： | NM24C04FLZN |
| 厂商： | FAIRCHILD SEMICONDUCTOR CORP |
| 元件分类： | PROM |
| 英文描述： | I2C Serial EEPROM |
| 中文描述： | 4K X 1 I2C/2-WIRE SERIAL EEPROM, PDIP8 |
| 封装： | PLASTIC, DIP-8 |
| 文件页数： | 8/14页 |
| 文件大小： | 104K |
| 代理商： | NM24C04FLZN |
8
www.fairchildsemi.com
NM24C04/05 Rev. G
N
EEPROM
Density
Number of
Page Blocks
Device Selection Inputs
Provided
Address Bits
Selecting Page Block
2k bit
1
A0
A1
A2
None
4k bit
2
—
A1
A2
A0
8k bit
4
—
—
A2
A0 and A1
16k bit
8
—
—
—
A0, A1 and A2
Pin Descriptions
Serial Clock (SCL)
The SCL input is used to clock all data into and out of the device.
Serial Data (SDA)
SDA is a bi-directional pin used to transfer data into and out of the
device. It is an open drain output and may be wire
–
ORed with any
number of open drain or open collector outputs.
Write Protect (WP) (NM24C05 Only)
If tied to V
CC
, PROGRAM operations onto the upper half (upper
2Kbit) of the memory will not be executed. READ operations are
possible. If tied to V
SS
, normal operation is enabled, READ/
WRITE over the entire memory is possible.
This feature allows the user to assign the upper half of the memory
as ROM which can be protected against accidental programming.
When write is disabled, slave address and word address will be
acknowledged but data will not be acknowledged.
This pin has an internal pull-down circuit. However, on systems
where write protection is not required it is recommended that this
pin is tied to V
SS
.
Device Selection Inputs A2, A1 and A0 (as
appropriate)
These inputs collectively serve as
“
chip select
”
signal to an
EEPROM when multiple EEPROMs are present on the same IIC
bus. Hence these inputs, if present, should be connected to V
CC
or V
in a unique manner to allow proper selection of an EEPROM
amongst multiple EEPROMs. During a typical addressing se-
quence, every EEPROM on the IIC bus compares the configura-
tion of these inputs to the respective 3 bit
“
Device/Page block
selection
”
information (part of slave address) to determine a valid
selection. For e.g. if the 3 bit
“
Device/Page block selection
”
is 1-
0-1, then the EEPROM whose
“
Device Selection inputs
”
(A2, A1
and A0) are connected to V
CC
-V
SS
-V
CC
respectively, is selected.
Depending on the density, only appropriate number of
“
Device
Selection inputs
”
are provided on an EEPROM. For every
“
Device
selection input
”
that is not present on the device, the correspond-
ing bit in the
“
Device/Page block selection
”
field is used to select
a
“
Page Block
”
within the device instead of the device itself.
Following table illustrates the above:
Note that even when just one EEPROM present on the IIC bus,
these pins should be tied to V
CC
or V
SS
to ensure proper termina-
tion.
Device Operation
The NM24C04/05 supports a bi-directional bus oriented protocol.
The protocol defines any device that sends data onto the bus as
a transmitter and the receiving device as the receiver. The device
controlling the transfer is the master and the device that is
controlled is the slave. The master will always initiate data
transfers and provide the clock for both transmit and receive
operations. Therefore, the NM24C04/05 will be considered a
slave in all applications.
Clock and Data Conventions
Data states on the SDA line can change only during SCL LOW.
SDA state changes during SCL HIGH are reserved for indicating
start and stop conditions. Refer to Figure 1 and Figure 2 on next
page.
Start Condition
All commands are preceded by the start condition, which is a
HIGH to LOW transition of SDA when SCL is HIGH. The NM24C04/
05 continuously monitors the SDA and SCL lines for the start
condition and will not respond to any command until this condition
has been met.
Stop Condition
All communications are terminated by a stop condition, which is a
LOW to HIGH transition of SDA when SCL is HIGH. The stop
condition is also used by the NM24C04/05 to place the device in
the standby power mode, except when a Write operation is being
executed, in which case a second stop condition is required after
t
WR
period, to place the device in standby mode.
相关PDF资料 |
PDF描述 |
|---|---|
| NM24C04FLZVM8 | I2C Serial EEPROM |
| NM24C04FLZVMT8 | I2C Serial EEPROM |
| NM24C04FLZVN | I2C Serial EEPROM |
| NM24C04FM8 | I2C Serial EEPROM |
| NM24C04LVMT8 | I2C Serial EEPROM |
相关代理商/技术参数 |
参数描述 |
|---|---|
| NM24C04FLZVM8 | 制造商:FAIRCHILD 制造商全称:Fairchild Semiconductor 功能描述:I2C Serial EEPROM |
| NM24C04FLZVMT8 | 制造商:FAIRCHILD 制造商全称:Fairchild Semiconductor 功能描述:I2C Serial EEPROM |
| NM24C04FLZVN | 制造商:FAIRCHILD 制造商全称:Fairchild Semiconductor 功能描述:I2C Serial EEPROM |
| NM24C04FM8 | 制造商:FAIRCHILD 制造商全称:Fairchild Semiconductor 功能描述:I2C Serial EEPROM |
| NM24C04FMT8 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:I2C Serial EEPROM |
发布紧急采购，3分钟左右您将得到回复。