- 您现在的位置：买卖IC网 > PDF目录19519 > NME2415DC (Murata Power Solutions Inc)CONV DC/DC 1W 24VIN 15V DIP SGL PDF资料下载
参数资料
| 型号： | NME2415DC |
| 厂商： | Murata Power Solutions Inc |
| 文件页数： | 2/4页 |
| 文件大小： | 0K |
| 描述： | CONV DC/DC 1W 24VIN 15V DIP SGL |
| 产品培训模块： | Low Power DC/DC Converters <5W |
| 标准包装： | 35 |
| 系列： | NME |
| 类型： | 隔离 |
| 输出数： | 1 |
| 电压 - 输入（最小）： | 21.6V |
| 电压 - 输入（最大）： | 26.4V |
| Voltage - Output 1： | 15V |
| 电流 - 输出（最大）： | 66mA |
| 电源（瓦） - 制造商系列： | 1W |
| 电压 - 隔离： | 1kV（1000V） |
| 安装类型： | 通孔 |
| 封装/外壳： | 8-DIP 模块（4 引线） |
| 尺寸/尺寸： | 0.39" L x 0.45" W x 0.27" H（9.9mm x 11.4mm x 6.9mm） |
| 包装： | 管件 |
| 工作温度： | 0°C ~ 70°C |
| 效率： | 80% |
| 电源（瓦特）- 最大： | 1W |
| 产品目录页面： | 2717 (CN2011-ZH PDF) |
| 其它名称： | 811-1493-5 |
NME 24V & 48V Series
Isolated 1W Single Output DC/DC Converters
ISOLATION CHARACTERISTICS
Parameter
Isolation test voltage
Resistance
Conditions
Flash tested for 1 second
Viso= 500VDC
Min.
1000
1
Typ.
Max.
Units
VDC
GΩ
GENERAL CHARACTERISTICS
Parameter
Switching frequency
Conditions
All types
Min.
Typ.
100
Max.
Units
kHz
TEMPERATURE CHARACTERISTICS
Parameter
Speci?cation
Storage
Conditions
All output types
Min.
0
-55
Typ.
Max.
70
150
Units
°C
Cooling
Free air convection
TEMPERATURE DERATING GRAPH
1.5
TOLERANCE ENVELOPE
+10%
1.0
70°C
+5%
V NOM
T y pical L
o ad Lin e
+2.5%
-2.5%
0.5 Safe Operating Area
125°C
-7.5%
0
0
50
100
150
10
25
50
75
100
Ambient Temperature (°C)
Output Load Current (%)
TECHNICAL NOTES
ISOLATION VOLTAGE
‘Hi Pot Test’, ‘Flash Tested’, ‘Withstand Voltage’, ‘Proof Voltage’, ‘Dielectric Withstand Voltage’ & ‘Isolation Test Voltage’ are all terms that relate to the same thing, a test voltage,
applied for a speci?ed time, across a component designed to provide electrical isolation, to verify the integrity of that isolation.
Murata Power Solutions NME series of DC/DC converters are all 100% production tested at their stated isolation voltage. This is 1kVDC for 1 second.
A question commonly asked is, “What is the continuous voltage that can be applied across the part in normal operation?”
For a part holding no speci?c agency approvals, such as the NME series, both input and output should normally be maintained within SELV limits i.e. less than 42.4V peak, or
60VDC. The isolation test voltage represents a measure of immunity to transient voltages and the part should never be used as an element of a safety isolation system. The part
could be expected to function correctly with several hundred volts offset applied continuously across the isolation barrier; but then the circuitry on both sides of the barrier must
be regarded as operating at an unsafe voltage and further isolation/insulation systems must form a barrier between these circuits and any user-accessible circuitry according to
safety standard requirements.
REPEATED HIGH-VOLTAGE ISOLATION TESTING
It is well known that repeated high-voltage isolation testing of a barrier component can actually degrade isolation capability, to a lesser or greater degree depending on materials,
construction and environment. The NME series has toroidal isolation transformers, with no additional insulation between primary and secondary windings of enameled wire. While
parts can be expected to withstand several times the stated test voltage, the isolation capability does depend on the wire insulation. Any material, including this enamel (typically
polyurethane) is susceptible to eventual chemical degradation when subject to very high applied voltages thus implying that the number of tests should be strictly limited. We
therefore strongly advise against repeated high voltage isolation testing, but if it is absolutely required, that the voltage be reduced by 20% from speci?ed test voltage.
This consideration equally applies to agency recognized parts rated for better than functional isolation where the wire enamel insulation is always supplemented by a further
insulation system of physical spacing or barriers.
www.murata-ps.com/support
KDC_NME2.E02 Page 2 of 4
相关PDF资料 |
PDF描述 |
|---|---|
| EPM7128SQC160-7 | IC MAX 7000 CPLD 128 160-PQFP |
| TRJA334K050RRJ | CAP TANT 0.33UF 50V 10% 1206 |
| TRJA224M050RRJ | CAP TANT 0.22UF 50V 20% 1206 |
| VI-B0H-CY-F2 | CONVERTER MOD DC/DC 52V 50W |
| EPM7256AETC100-7N | IC MAX 7000 CPLD 256 100-TQFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| NME2415M | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Analog IC |
| NME2415S | 功能描述:DC/DC转换器 1 WATT OUTPUT 24-15V RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸: |
| NME2415SC | 功能描述:DC/DC转换器 1W Single Output 24V to 15V 66mA RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸: |
| NME48 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Isolated 1WSingle Output |
| NME480 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Isolated 1WSingle Output |
发布紧急采购，3分钟左右您将得到回复。