- 您现在的位置：买卖IC网 > PDF目录19654 > NMR120C (Murata Power Solutions Inc)CONV DC/DC 1W 24VIN 15V SIP SGL PDF资料下载
参数资料
| 型号： | NMR120C |
| 厂商： | Murata Power Solutions Inc |
| 文件页数： | 2/5页 |
| 文件大小： | 0K |
| 描述： | CONV DC/DC 1W 24VIN 15V SIP SGL |
| 产品培训模块： | Low Power DC/DC Converters <5W |
| 标准包装： | 25 |
| 系列： | NMR |
| 类型： | 隔离 |
| 输出数： | 1 |
| 电压 - 输入（最小）： | 21.6V |
| 电压 - 输入（最大）： | 26.4V |
| Voltage - Output 1： | 15V |
| 电流 - 输出（最大）： | 67mA |
| 电源（瓦） - 制造商系列： | 1W |
| 电压 - 隔离： | 1kV（1000V） |
| 安装类型： | 通孔 |
| 封装/外壳： | 7-SIP 模块（4 引线） |
| 尺寸/尺寸： | 0.77" L x 0.24" W x 0.39" H（19.6mm x 6.1mm x 9.9mm） |
| 包装： | 管件 |
| 工作温度： | -40°C ~ 85°C |
| 效率： | 80% |
| 电源（瓦特）- 最大： | 1W |
| 产品目录页面： | 2717 (CN2011-ZH PDF) |
| 其它名称： | 811-1574-5 |
NMR Series
Isolated 1W Single Output DC/DC Converters
GENERAL CHARACTERISTICS
Parameter
Conditions
Min.
Typ.
Max.
Units
5V input types
110
Switching frequency
12V input types
15V input types
24V input types
160
90
80
kHz
TEMPERATURE CHARACTERISTICS
Parameter
Speci?cation
Storage
Case Temperature above ambient
Conditions
All output types
5V output types
All other output types
Min.
-40
-50
Typ.
33
28
Max.
85
130
Units
°C
Cooling
TOLERANCE ENVELOPES
Free air convection
NMR118
NMR113, NMR 114, NMR119, NMR120
All other types
l a
Lo
o Line
a lL o
+7%
+4.5%
+2%
V NOM
Typic
a
d L in e
0%
-2.5%
-5%
+4%
+2%
V NOM
T y pica l L
ad
+1%
-1%
-3%
+10%
+5%
V NOM
T y pi c
a d L
i n e
+2.5%
-2.5%
-7.5%
10
25
50
75
100
10
25
50
75
100
10
25
50
75
100
Output Load Current (%)
Output Load Current (%)
Output Load Current (%)
The voltage tolerance envelope shows typical load regulation characteristics for this product series. The tolerance envelope is the maximum output voltage variation due to
changes in output loading.
TECHNICAL NOTES
ISOLATION VOLTAGE
‘Hi Pot Test’, ‘Flash Tested’, ‘Withstand Voltage’, ‘Proof Voltage’, ‘Dielectric Withstand Voltage’ & ‘Isolation Test Voltage’ are all terms that relate to the same thing, a test voltage,
applied for a speci?ed time, across a component designed to provide electrical isolation, to verify the integrity of that isolation.
Murata Power Solutions NMR series of DC/DC converters are all 100% production tested at their stated isolation voltage. This is 1kVDC for 1 second.
A question commonly asked is, “What is the continuous voltage that can be applied across the part in normal operation?”
For a part holding no speci?c agency approvals, such as the NMR series, both input and output should normally be maintained within SELV limits i.e. less than 42.4V peak, or
60VDC. The isolation test voltage represents a measure of immunity to transient voltages and the part should never be used as an element of a safety isolation system. The part
could be expected to function correctly with several hundred volts offset applied continuously across the isolation barrier; but then the circuitry on both sides of the barrier must
be regarded as operating at an unsafe voltage and further isolation/insulation systems must form a barrier between these circuits and any user-accessible circuitry according to
safety standard requirements.
REPEATED HIGH-VOLTAGE ISOLATION TESTING
It is well known that repeated high-voltage isolation testing of a barrier component can actually degrade isolation capability, to a lesser or greater degree depending on materials,
construction and environment. The NMR series has toroidal isolation transformers, with no additional insulation between primary and secondary windings of enameled wire. While
parts can be expected to withstand several times the stated test voltage, the isolation capability does depend on the wire insulation. Any material, including this enamel (typically
polyurethane) is susceptible to eventual chemical degradation when subject to very high applied voltages thus implying that the number of tests should be strictly limited. We
therefore strongly advise against repeated high voltage isolation testing, but if it is absolutely required, that the voltage be reduced by 20% from speci?ed test voltage.
This consideration equally applies to agency recognized parts rated for better than functional isolation where the wire enamel insulation is always supplemented by a further
insulation system of physical spacing or barriers.
RoHS COMPLIANCE INFORMATION
This series is compatible with RoHS soldering systems with a peak wave solder temperature of 300oC for 10 seconds. The pin termination ?nish
on this product series is Tin Plate, Hot Dipped over Matte Tin with Nickel Preplate. The series is backward compatible with Sn/Pb soldering
systems.
For further information, please visit www.murata-ps.com/rohs
www.murata-ps.com/support
KDC_NMR.E01 Page 2 of 5
相关PDF资料 |
PDF描述 |
|---|---|
| AD7814ARMZ | IC DGTL TEMP SENSOR 10BIT 8-MSOP |
| LC4384B-35TN176C | IC CPLD 384MACROCELLS 176TQFP |
| EEC06DRAN | CONN EDGECARD 12POS R/A .100 SLD |
| LC4384V-5TN176I | IC CPLD 384MACROCELLS 176TQFP |
| ESC06DREF | CONN EDGECARD 12POS .100 EYELET |
相关代理商/技术参数 |
参数描述 |
|---|---|
| NMR120K | 制造商:NIC Components Corp 功能描述: |
| NMR121K | 制造商:NIC Components Corp 功能描述: |
| NMR124K | 制造商:NIC Components Corp 功能描述: |
| NMR127.0 | 制造商:NIC Components Corp 功能描述: |
| NMR127K | 制造商:NIC Components Corp 功能描述: |
发布紧急采购，3分钟左右您将得到回复。