- 您现在的位置：买卖IC网 > PDF目录8306 > NMXD0512SOC (Murata Power Solutions Inc)CONV DC/DC 5W 5VIN 12V DIP REG PDF资料下载
参数资料
| 型号： | NMXD0512SOC |
| 厂商： | Murata Power Solutions Inc |
| 文件页数： | 2/3页 |
| 文件大小： | 0K |
| 描述： | CONV DC/DC 5W 5VIN 12V DIP REG |
| 标准包装： | 12 |
| 系列： | NMXSO |
| 类型： | 隔离 |
| 输出数： | 2 |
| 电压 - 输入（最小）： | 4.5V |
| 电压 - 输入（最大）： | 5.5V |
| Voltage - Output 1： | 12V |
| Voltage - Output 2： | -12V |
| 电流 - 输出（最大）： | 235mA，235mA |
| 电源（瓦） - 制造商系列： | 5W |
| 电压 - 隔离： | 1kV（1000V） |
| 安装类型： | 通孔 |
| 封装/外壳： | 5-DIP 模块 |
| 尺寸/尺寸： | 1.59" L x 0.93" W x 0.39" H（40.4mm x 23.6mm x 9.9mm） |
| 包装： | 管件 |
| 工作温度： | 0°C ~ 70°C |
| 效率： | 65% |
| 电源（瓦特）- 最大： | 5W |
| 其它名称： | 811-1613-5 |
NMXSO Series
Isolated 5W Regulated Single & Dual Output DC/DC Converters
ISOLATION CHARACTERISTICS
Parameter
Isolation test voltage
Resistance
Conditions
Flash tested for 1 second
Viso= 1000VDC
Min.
1000
1
Typ.
Max.
Units
VDC
GΩ
GENERAL CHARACTERISTICS
Parameter
Switching frequency
Conditions
All input types
Min.
Typ.
70
Max.
Units
kHz
TEMPERATURE CHARACTERISTICS
Parameter
Speci?cation
Storage
Conditions
All output types
Min.
0
-55
Typ.
Max.
70
100
Units
°C
Case Temperature above ambient
Cooling
All output types
Free air convection
30
RoHS COMPLIANCE INFORMATION
This series is compatible with RoHS soldering systems with a peak wave solder temperature of 300oC
for 10 seconds. The pin termination ?nish on this product series is Matte Tin over Nickel Preplate. The
series is backward compatible with Sn/Pb soldering systems.
For further information, please visit www.murata-ps.com/rohs
TECHNICAL NOTES
ISOLATION VOLTAGE
‘Hi Pot Test’, ‘Flash Tested’, ‘Withstand Voltage’, ‘Proof Voltage’, ‘Dielectric Withstand Voltage’ & ‘Isolation Test Voltage’ are all terms that relate to the same thing, a test voltage,
applied for a speci?ed time, across a component designed to provide electrical isolation, to verify the integrity of that isolation.
Murata Power Solutions NMXSO series of DC/DC converters are all 100% production tested at their stated isolation voltage. This is 1kVDC for 1 second.
A question commonly asked is, “What is the continuous voltage that can be applied across the part in normal operation?”
For a part holding no speci?c agency approvals, such as the NMXSO series, both input and output should normally be maintained within SELV limits i.e. less than 42.4V peak, or
60VDC. The isolation test voltage represents a measure of immunity to transient voltages and the part should never be used as an element of a safety isolation system. The part
could be expected to function correctly with several hundred volts offset applied continuously across the isolation barrier; but then the circuitry on both sides of the barrier must
be regarded as operating at an unsafe voltage and further isolation/insulation systems must form a barrier between these circuits and any user-accessible circuitry according to
safety standard requirements.
REPEATED HIGH-VOLTAGE ISOLATION TESTING
It is well known that repeated high-voltage isolation testing of a barrier component can actually degrade isolation capability, to a lesser or greater degree depending on materials,
construction and environment. The NMXSO series has toroidal isolation transformers, with no additional insulation between primary and secondary windings of enameled wire.
While parts can be expected to withstand several times the stated test voltage, the isolation capability does depend on the wire insulation. Any material, including this enamel
(typically polyurethane) is susceptible to eventual chemical degradation when subject to very high applied voltages thus implying that the number of tests should be strictly limited.
We therefore strongly advise against repeated high voltage isolation testing, but if it is absolutely required, that the voltage be reduced by 20% from speci?ed test voltage.
This consideration equally applies to agency recognized parts rated for better than functional isolation where the wire enamel insulation is always supplemented by a further
insulation system of physical spacing or barriers.
www.murata-ps.com/support
KDC_NMXSO.E01 Page 2 of 3
相关PDF资料 |
PDF描述 |
|---|---|
| 74LVCH16374ADGG:51 | IC 16BIT EDGE TRIG D FF 48TSSOP |
| 74LVCH16374ADGG,51 | IC 16BIT EDGE TRIG D FF 48TSSOP |
| MS27466T25A29SALC | CONN HSG RCPT 29POS WALL MT SCKT |
| MS27467T17F6A | CONN HSG PLUG 6POS STRGHT PINS |
| MS27467E17F6A | CONN HSG PLUG 6POS STRGHT PINS |
相关代理商/技术参数 |
参数描述 |
|---|---|
| NMXD0512U | 功能描述:DC/DC转换器 5W DUAL OUT 5-12V RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸: |
| NMXD0512UC | 功能描述:DC/DC转换器 5Vin +/-12Vout 5W +/-0.208A DIP un-Reg RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸: |
| NMXD0515SO | 功能描述:DC/DC转换器 5W DUAL OUT 15V RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸: |
| NMXD0515SOC | 功能描述:DC/DC转换器 5Vin +/-15Vout +/-0.2A 5W DIP Reg RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸: |
| NMXD0515U | 制造商:Murata Power Solutions 功能描述:DC/DC CONVERTER 5W +/-15V |
发布紧急采购，3分钟左右您将得到回复。