- 您现在的位置：买卖IC网 > PDF目录19516 > NPH10S2412IC (Murata Power Solutions Inc)CONV DC/DC 10W24VIN 12.1VOUT DIP PDF资料下载
参数资料
| 型号： | NPH10S2412IC |
| 厂商： | Murata Power Solutions Inc |
| 文件页数： | 4/8页 |
| 文件大小： | 0K |
| 描述： | CONV DC/DC 10W24VIN 12.1VOUT DIP |
| 产品培训模块： | Medium Power Industrial DC/DC Converters 5 ~ 60W |
| 标准包装： | 15 |
| 系列： | NPH10S |
| 类型： | 隔离 |
| 输出数： | 1 |
| 电压 - 输入（最小）： | 18V |
| 电压 - 输入（最大）： | 36V |
| Voltage - Output 1： | 12.1V |
| 电流 - 输出（最大）： | 830mA |
| 电源（瓦） - 制造商系列： | 10W |
| 电压 - 隔离： | 1.5kV（1500V） |
| 安装类型： | 通孔 |
| 封装/外壳： | 6-DIP 模块 |
| 尺寸/尺寸： | 1.26" L x 0.98" W x 0.39" H（32.0mm x 24.9mm x 9.9mm） |
| 包装： | 管件 |
| 工作温度： | -40°C ~ 110°C |
| 效率： | 86% |
| 电源（瓦特）- 最大： | 10W |
| 产品目录页面： | 2718 (CN2011-ZH PDF) |
| 其它名称： | 811-1628-5 |
NPH10S Series
Isolated 10W Single Output DC/DC Converters
APPLICATION NOTES (continued)
SYNCHRONISATION
The converter frequency may be synchronised to an external frequency by connecting a negative going pulse to the SS pin. The drive signal is typically
8V to 12V amplitude and 100ns to 200ns duration. A suitable circuit consists of a CMOS timer (TLC555) connected as an oscillator or as a pulse shaper.
Its logic output (not the discharge output) should be connected via a 4.7nF capacitor to the converter pin. The synchronised frequency is above the free
running value. However, the free running frequency can be lowered, so that sychronisation may include frequencies near or below the natural value.
An example of a practical circuit is shown below, which uses a zener diode to lower the natural frequency. Several converters of this family may be
synchronised from the same reference provided the waveform can be maintained by the use of an adequate driver circuit. If the rise time is more than
20ns, for example, synchronisation may not be achieved over the speci?ed frequency range.
For best ef?ciency, set the frequency within the speci?ed range of its natural state.
TECHNICAL NOTES
ISOLATION VOLTAGE
‘Hi Pot Test’, ‘Flash Tested’, ‘Withstand Voltage’, ‘Proof Voltage’, ‘Dielectric Withstand Voltage’ & ‘Isolation Test Voltage’ are all terms that relate to the same thing, a test voltage,
applied for a speci?ed time, across a component designed to provide electrical isolation, to verify the integrity of that isolation.
Murata Power Solutions NPH10S series of dc/dc converters are all 100% production tested at their stated isolation voltage. This is 1500V DC for 1 second.
A question commonly asked is, “What is the continuous voltage that can be applied across the part in normal operation?”
The NPH10S series has been recognized by Underwriters Laboratory, both input and output should normally be maintained within SELV limits i.e. less than 42.4V peak, or 60VDC.
The isolation test voltage represents a measure of immunity to transient voltages and the part should never be used as an element of a safety isolation system. The part could be
expected to function correctly with several hundred volts offset applied continuously across the isolation barrier; but then the circuitry on both sides of the barrier must be regarded
as operating at an unsafe voltage and further isolation/insulation systems must form a barrier between these circuits and any user-accessible circuitry according to safety standard
requirements.
REPEATED HIGH-VOLTAGE ISOLATION TESTING
It is well known that repeated high-voltage isolation testing of a barrier component can actually degrade isolation capability, to a lesser or greater degree depending on materi-
als, construction and environment. While manufactured parts can withstand several times the stated test voltage, the isolation capability does depend on the wire insulation. Any
material, including this enamel (typically polyurethane) is susceptible to eventual chemical degradation when subject to very high applied voltages thus implying that the number of
tests should be strictly limited. We therefore strongly advise against repeated high voltage isolation testing, but if it is absolutely required, that the voltage be reduced by 20% from
speci?ed test voltage.
www.murata-ps.com/support
KDC_NPH10SC.J03 Page 4 of 8
相关PDF资料 |
PDF描述 |
|---|---|
| RS-123.3D/H2 | CONV DC/DC 2W 9-18VIN +/-3.3V |
| RCA10DTMN | CONN EDGECARD 20POS R/A .125 SLD |
| KCM55LR72A475KH01K | CAP CER 4.7UF 100V 10% X7R 2220 |
| R15P209S/X2/P/R6.4 | CONV DC/DC 2W 15VIN 09VOUT |
| MAX6642ATT90+T | IC TEMP SENSOR SMBUS 6-TDFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| NPH10S2412IC | 制造商:Murata Power Solutions 功能描述:DC-DC Converter Supply Voltage:24V |
| NPH10S2415EI | 制造商:CANDD 制造商全称:C&D Technologies 功能描述:Isolated 10W Single Output DC/DC Converters |
| NPH10S2415EIC | 功能描述:DC/DC转换器 24Vin 15.1Vout 0.67A Isolated 10W RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸: |
| NPH10S2415I | 功能描述:DC/DC转换器 10W 24V IN 15.1 OUT RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸: |
| NPH10S2415IC | 功能描述:DC/DC转换器 10W 24V IN 15.1 OUT Single Output RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸: |
发布紧急采购，3分钟左右您将得到回复。